Modeling and simulation of non-uniformity in the planarization process

被引：0
|
作者：
Thin-Lin Horng
机构：
[1] Kun-Shan University,Department of Mechanical Engineering
来源：
The International Journal of Advanced Manufacturing Technology | 2008年 / 39卷
关键词：
Non-uniformity; Material removal; Deformation; Planarization;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
The estimation of surface non-uniformity under various machining parameters (such as dressing force, diamond density of dresser, rotational speed of dresser, different machining paths, etc.) is essential to the planarization process. Based on abrasive theory and the deformation analyses of a polishing pad, this paper develops a model to calculate material removal in the planarization process and then calculate non-uniformity by using this model. The results reveal that the non-uniformity is in good agreement with experimental data. Moreover, it was found that the non-uniformity decreased when the dressing time increased.
引用
收藏
页码：512 / 520
页数：8
相关论文
共 50 条
  • [1] Modeling and simulation of non-uniformity in the planarization process
    Horng, Thin-Lin
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2008, 39 (5-6): : 512 - 520
  • [2] Improvement of via dishing and non-uniformity in TSV chemical mechanical planarization
    Rao, Can
    Wang, Tongqing
    Wang, Jie
    Liu, Yuhong
    Lu, Xinchun
    MICROELECTRONIC ENGINEERING, 2016, 151 : 38 - 46
  • [3] Modeling of pattern density dependent pressure non-uniformity at a die scale for ILD chemical mechanical planarization
    Choi, JH
    Dornfeld, DA
    ADVANCES IN CHEMICAL-MECHANICAL POLISHING, 2004, 816 : 101 - 106
  • [4] Thermal imager non-uniformity sources modeling
    Guadagnoli, Emanuele
    Giunti, Claudio
    Mariani, Paolo
    Olivieri, Monica
    Porta, Antonio
    Sozzi, Barbara
    Zatti, Stefano
    INFRARED IMAGING SYSTEMS: DESIGN, ANALYSIS, MODELING, AND TESTING XXII, 2011, 8014
  • [5] Etch Planarization - A New Approach to Correct Non-Uniformity Post Chemical Mechanical Polishing
    Shen, Meihua
    Zhou, Baosuo
    Zhou, Yifeng
    Hoang, John
    Bowers, Jim
    Bailey, Andrew
    Pape, Eric
    Singh, Harmeet
    Dasaka, Ravi K.
    Wise, Rich
    2014 25TH ANNUAL SEMI ADVANCED SEMICONDUCTOR MANUFACTURING CONFERENCE (ASMC), 2014, : 423 - 427
  • [6] A New Etch Planarization Technology to Correct Non-Uniformity Post Chemical Mechanical Polishing
    Shen, Meihua
    Zhou, Baosuo
    Zhou, Yifeng
    Hoang, John
    Bowers, Jim
    Bailey, Andrew D., III
    Pape, Eric
    Singh, Harmeet
    Wise, Rich
    Dasaka, Ravi K.
    IEEE TRANSACTIONS ON SEMICONDUCTOR MANUFACTURING, 2015, 28 (04) : 502 - 507
  • [7] Effect of Conditioning Parameters on Surface Non-uniformity of Polishing Pad in Chemical Mechanical Planarization
    Qin, N.
    Guo, D. M.
    Kang, R. K.
    Huo, F. W.
    ADVANCES IN ABRASIVE TECHNOLOGY XI, 2009, 389-390 : 498 - 503
  • [8] Effects of kinematic forms on material removal rate and non-uniformity in chemical mechanical planarization
    Wang, C. L.
    Jin, Z. J.
    Kang, R. X.
    ADVANCES IN ABRASIVE MACHINING AND SURFACING TECHNOLOGIES, PROCEEDINGS, 2006, : 287 - +
  • [9] Numerical simulation of the impact of urban non-uniformity on precipitation
    Song, Yuqiang
    Liu, Hongnian
    Wang, Xueyuan
    Zhang, Ning
    Sun, Jianning
    ADVANCES IN ATMOSPHERIC SCIENCES, 2016, 33 (06) : 783 - 793
  • [10] Thermal simulation and evaluation for non-uniformity detection of electrode
    Ye, Wei-Biao
    APPLIED THERMAL ENGINEERING, 2016, 96 : 583 - 592
12345