Effect of Mechanical Vibration on the Kinetics of Dehydrogenation and Structure Formation of TiH2 Powder Compacts During Electron Beam Sintering

被引：0
|
作者：
Ye. G. Biba
P. I. Loboda
机构：
[1] National Technical University of Ukraine “Kyiv Polytechnic Institute”,
来源：
Powder Metallurgy and Metal Ceramics | 2015年 / 53卷
关键词：
titanium hydride; mechanical vibrations; stress; hardness; ductility; compressive strength;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
The effect of mechanical vibrations on the structure formation and mechanical properties of compacts during electron beam sintering is investigated. Using optical microscopy, continuous indentation, and X-ray diffraction, it was established that imposing mechanical vibrations decreases the average titanium grain size by a factor of 1.5–2 and induces residual compressive stresses in the sintered titanium compact. Due to the stresses, greater density, and smaller grains, the ductility and compressive strength of the compacts sintered under mechanical vibrations are higher than those of the compacts sintered in conventional way.
引用
收藏
页码：628 / 633
页数：5
相关论文
共 45 条
  • [41] Effect of mechanical milling on the harmonic structure development during spark plasma sintering of Ti-5Al-2Sn-4Zr-4Mo-2Cr-1Fe β-metastable titanium alloy (β-Cez alloy)
    Sharma, Bhupendra
    Denand, Benoit
    Harcuba, Petr
    Geandier, Guillaume
    Ameyama, Kei
    Dirras, Guy
    Aeby-Gautier, Elisabeth
    JOURNAL OF ALLOYS AND COMPOUNDS, 2021, 860
  • [42] ELECTRON-BEAM AND PLASMA OXIDATION-RESISTANT AND THERMAL-BARRIER COATINGS DEPOSITED ON TURBINE BLADES USING CAST AND POWDER Ni(Co)CrAlY(Si) ALLOYS PRODUCED BY ELECTRON BEAM MELTING III. FORMATION, STRUCTURE, AND CHEMICAL AND PHASE COMPOSITION OF THERMAL-BARRIER Ni(Co)CrAlY/ZrO2-Y2O3 COATINGS PRODUCED BY PHYSICAL VAPOR DEPOSITION IN ONE PROCESS CYCLE
    Grechanyuk, M. I.
    Grechanyuk, I. M.
    Yevterev, Y. N.
    Grechanyuk, V. G.
    Prikhna, T. O.
    Bagliuk, G. A.
    Hots, V. I.
    Khomenko, O. V.
    Dudnik, O. V.
    Matsenko, O. V.
    POWDER METALLURGY AND METAL CERAMICS, 2022, 61 (5-6) : 328 - 336
  • [43] Electron-Beam and Plasma Oxidation-Resistant and Thermal-Barrier Coatings Deposited on Turbine Blades Using Cast and Powder Ni (Co)CrAlY (Si) Alloys Produced by Electron Beam Melting III. Formation, Structure, and Chemical and Phase Composition of Thermal-Barrier Ni(Co)CrAlY/ZrO2–Y2O3 Coatings Produced by Physical Vapor Deposition in One Process Cycle
    M.I. Grechanyuk
    I.M. Grechanyuk
    Y.N. Yevterev
    V.G. Grechanyuk
    T.O. Prikhna
    G.A. Bagliuk
    V.I. Hots
    O.V. Khomenko
    O.V. Dudnik
    O.V. Matsenko
    Powder Metallurgy and Metal Ceramics, 2022, 61 : 328 - 336
  • [44] Effect of semifinished rolled product cooling rate during controlled rolling on the condition of microalloyed steel hot-worked austenite, final microstructure, and mechanical properties. Part 2. Study of the effect of semifinished rolled product cooling rate on ferrite-bainite structure formation*
    Yu. D. Morozov
    I. F. Pemov
    E. A. Goli-Oglu
    D. V. Nizhelsky
    Metallurgist, 2012, 56 : 137 - 146
  • [45] Effect of semifinished rolled product cooling rate during controlled rolling on the condition of microalloyed steel hot-worked austenite, final microstructure, and mechanical properties. Part 2. Study of the effect of semifinished rolled product cooling rate on ferrite-bainite structure formation
    Morozov, Yu. D.
    Pemov, I. F.
    Goli-Oglu, E. A.
    Nizhelsky, D. V.
    METALLURGIST, 2012, 56 (1-2) : 137 - 146
12345