Evaluation of Cu-Zr-Ti-In Bulk Metallic Glasses via Nanoindentation

被引：0
|
作者：
J. L. Wu
Y. Pan
J. H. Pi
机构：
[1] Southeast University,School of Materials Science and Engineering, Jiangsu Key Laboratory for Advanced Metallic Materials
[2] Nanjing Institute of Technology,School of Materials Engineering
来源：
Journal of Materials Engineering and Performance | 2013年 / 22卷
关键词：
bulk metallic glass; hardness; nanoindentation test; Young’s modulus;
D O I：
暂无
中图分类号：
学科分类号：
摘要：
In this paper, the mechanical properties of two bulk metallic glasses, Cu60Zr34Ti5In1 and Cu58Zr34Ti5In3, have been evaluated by nanoindentation tests. The hardness and Young’s modulus of as-cast Cu60Zr34Ti5In1 bulk metallic glass increase from the center to the edge of the rod, but Cu58Zr34Ti5In3 shows an inverse trend. The Young’s modulus of Cu58Zr34Ti5In3 is lower than that of Cu60Zr34Ti5In1. For both bulk metallic glasses, serrations on the nanoindentation load-displacement curves depend not only on loading rate but also on the maximum load. Alternatively, the onset position of the appearance of serrations on the curves increases with the loading rate. In addition, the hardness of both samples decreases as the size of the indent increases due to indentation size effects.
引用
收藏
页码：2288 / 2292
页数：4
相关论文
共 50 条
  • [31] Zr-Ti-Al-Fe-Cu bulk metallic glasses for biomedical device application
    Han, Kai-Ming
    Jiang, Hui
    Wang, Ying-Min
    Qiang, Jian-Bing
    RARE METALS, 2021, 40 (05) : 1239 - 1246
  • [32] The thermal stability and mechanical behaviors of Zr-Cu-Ni-Ti-Be bulk metallic glasses
    Tsau, Chun-Huei
    Wu, Chih-Chung
    Wu, Shyue-Sheng
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2007, 182 (1-3) : 257 - 261
  • [33] A new way of designing bulk metallic glasses in Cu-Ti-Zr-Ni system
    Yang, Y. J.
    Xing, D. W.
    Li, C. P.
    Wei, S. D.
    Sun, J. K.
    Shen, Q. K.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 448 (1-2): : 15 - 19
  • [34] Zr-Ti-Al-Fe-Cu bulk metallic glasses for biomedical device application
    Kai-Ming Han
    Hui Jiang
    Ying-Min Wang
    Jian-Bing Qiang
    RareMetals, 2021, 40 (05) : 1239 - 1246
  • [35] Computer simulations of nanoindentation in Mg-Cu and Cu-Zr metallic glasses
    Paduraru, A.
    Andersen, U. G.
    Thyssen, A.
    Bailey, N. P.
    Jacobsen, K. W.
    Schiotz, J.
    MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING, 2010, 18 (05)
  • [36] Zr-(Cu,Ag)-Al bulk metallic glasses
    Jiang, Q. K.
    Wang, X. D.
    Nie, X. P.
    Zhang, G. Q.
    Ma, H.
    Fecht, H. -J.
    Bednarcik, J.
    Franz, H.
    Liu, Y. G.
    Cao, Q. P.
    Jiang, J. Z.
    ACTA MATERIALIA, 2008, 56 (08) : 1785 - 1796
  • [37] Inelastic deformation induced by cyclic nanoindentation in Zr-based bulk metallic glasses
    Tekaya, A.
    Labdi, S.
    Benameur, T.
    Jellad, A.
    Aubert, P.
    Maciejak, O.
    MATERIAUX & TECHNIQUES, 2011, 99 (04): : 471 - 481
  • [38] Formation and Corrosion Behavior of Mechanically-Alloyed Cu-Zr-Ti Bulk Metallic Glasses
    Lee, Pee-Yew
    Cheng, Yeh-Ming
    Chen, Jyun-Yu
    Hu, Chia-Jung
    METALS, 2017, 7 (04):
  • [39] The oxidation behavior of Cu–Zr–Ti–base bulk metallic glasses in air at 350–500 °C
    H. H. Hsieh
    W. Kai
    W. L. Jang
    R. T. Huang
    P. Y. Lee
    W. H. Wang
    Oxidation of Metals, 2007, 67 : 179 - 192
  • [40] Formation of Ti-Zr-Cu-Ni-Sn-Si bulk metallic glasses with good plasticity
    Yin, Enhuai
    Zhang, Min
    Pang, Shujie
    Zhao, Xiangjin
    Zhang, Tao
    JOURNAL OF ALLOYS AND COMPOUNDS, 2010, 504 : S10 - S13
12345