Sharpening helical bits with curvilinear cutting edges at the rear surface

被引：4
|
作者：
Petukhov Y.E. [1 ]
Vodovozov A.A. [1 ]
机构：
[1] Stankin Moscow State Technical University, Moscow
来源：
Russian Engineering Research | 2015年 / 35卷 / 9期
关键词：
curvilinear cutting edge; helical bit; rear surface; sharpening;
D O I：
10.3103/S1068798X15090178
中图分类号：
学科分类号：
摘要：
Sharpening of the curvilinear cutting edges at the rear surface of helical bits is considered. A mathematic model of the rear surfaces takes account of the bit parameters and the distribution of the rear angles along the cutting edge. The position of the grinding wheel in sharpening is determined. © 2015, Allerton Press, Inc.
引用
收藏
页码：670 / 673
页数：3
相关论文
共 50 条
  • [21] Application of advanced surface engineering treatments to multi-point cutting edges
    Univ of Northumbria at Newcastle, Newcastle-upon-Tyne, United Kingdom
    Surface and Coatings Technology, 1998, 108-109 (1-3): : 612 - 619
  • [22] Modeling and numerical simulation for the machining of helical surface profiles on cutting tools
    Sun, Yuwen
    Wang, Jun
    Guo, Dongming
    Zhang, Qiang
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2008, 36 (5-6): : 525 - 534
  • [23] Modeling and numerical simulation for the machining of helical surface profiles on cutting tools
    Yuwen Sun
    Jun Wang
    Dongming Guo
    Qiang Zhang
    The International Journal of Advanced Manufacturing Technology, 2008, 36 : 525 - 534
  • [24] Uniform Ray Description for the PO Scattering by Vertices in Curved Surface With Curvilinear Edges and Relatively General Boundary Conditions
    Albani, Matteo
    Carluccio, Giorgio
    Pathak, Prabhakar H.
    IEEE TRANSACTIONS ON ANTENNAS AND PROPAGATION, 2011, 59 (05) : 1587 - 1596
  • [25] Technological basis of the surface roughness parameters of machine parts produced by tools with cutting edges
    Suslov, A.G.
    Soviet engineering research, 1988, 8 (01): : 52 - 55
  • [26] A new method for modeling edges of a toroidal cutting surface of solid ceramic end mills
    Pivkin, Petr M.
    Nadykto, Alexey B.
    Grechishnikov, Vladimir A.
    Volosova, Marina A.
    Minin, Ilya, V
    Grigoriev, Sergey N.
    EMERGING IMAGING AND SENSING TECHNOLOGIES FOR SECURITY AND DEFENCE V; AND ADVANCED MANUFACTURING TECHNOLOGIES FOR MICRO- AND NANOSYSTEMS IN SECURITY AND DEFENCE III, 2020, 11540
  • [27] Influence of solid lubricants on the wear at the rear surface of hard-alloy tools in discontinuous cutting
    Solodkov V.A.
    Tibirkova M.A.
    Solodkov, V. A., 1600, Allerton Press Inc, 18 West 27th Street, New York, NY 10001, United States (33): : 48 - 50
  • [28] Bio-inspired self-sharpening cutting tool surface for finish hard turning of steel
    Jiang, Wenping
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2014, 63 (01) : 517 - 520
  • [29] A grinding process method of solid end mills groove with segmented unequal helical angles by cutting edges offset and interference
    Li, Yong
    Ding, Guofu
    Yang, Zhihui
    Xia, Changjiu
    Jiang, Lei
    JOURNAL OF MANUFACTURING PROCESSES, 2023, 102 : 849 - 864
  • [30] Particular Solution of Cutting Tool Path Applied on Helical Surface with Circular Profile
    Nieszporek, Tadeusz
    Boral, Piotr
    Golebski, Rafal
    TEHNICKI VJESNIK-TECHNICAL GAZETTE, 2019, 26 (01): : 22 - 28
12345