A rotary drum dryer for palm sterilization: preliminary study of flow and heat transfer using CFD

被引：1
|
作者：
Hanifarianty, S. [1 ]
Legwiriyakul, A. [2 ,3 ]
Alimalbari, A. [2 ,3 ]
Nuntadusit, C. [1 ,2 ,3 ]
Theppaya, T. [1 ,2 ,3 ]
Wae-Hayee, M. [1 ,2 ,3 ]
机构：
[1] Prince Songkla Univ, Fac Engn, Energy Technol, Hat Yai 90112, Songkhla, Thailand
[2] Prince Songkla Univ, Fac Engn, Energy Technol Res Ctr, Hat Yai 90112, Songkhla, Thailand
[3] Prince Songkla Univ, Fac Engn, Dept Mech Engn, Hat Yai 90112, Songkhla, Thailand
来源：
8TH TSME-INTERNATIONAL CONFERENCE ON MECHANICAL ENGINEERING (TSME-ICOME 2017) | 2018年 / 297卷
关键词：
D O I：
10.1088/1757-899X/297/1/012030
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Preliminary study in this article, the flow and the heat transfer of rotary drum dryer were simulated by using Computational Fluid Dynamics (CFD). A 3D modelling of rotary drum dryer including ambient air was created by considering transient simulation. The temperature distributions on rotary drum dryer surfaces of experimental setup during heating detected by using infrared camera were given to be boundary conditions of modelling. The average temperature at the surface of the drum lids was 80 degrees C, and the average temperature on the heated surface of the drum was 130 degrees C. The results showed that the internal temperature of air in drum modelling was increased relating on time dependent. The final air temperature inside the drum modelling was similar to the measurement results.
引用
收藏
页数：8
相关论文
共 50 条
  • [31] An experimental setup for studying conduction and radiation heat transfer in a rotary drum
    Bheda, Bhaumik
    Tronstad, Joel
    Emady, Heather
    CHEMICAL ENGINEERING SCIENCE, 2025, 302
  • [32] HEAT-TRANSFER FROM WALL TO PARTICLES BED IN A ROTARY DRUM
    ITO, N
    OBATA, K
    HAKUTA, T
    YOSHITOME, H
    KAGAKU KOGAKU RONBUNSHU, 1983, 9 (06) : 628 - 634
  • [33] Experimental study on drying of chilli in a combined microwave-vacuum-rotary drum dryer
    Kaensup, W
    Chutima, S
    Wongwises, S
    DRYING TECHNOLOGY, 2002, 20 (10) : 2067 - 2079
  • [34] A STUDY ON THE FLUID FLOW AND HEAT TRANSFER FOR A POROUS ARCHITECTED HEAT SINK USING THE IDEA OF CFD MODELLING
    Ali, Mohamed I. Hassan
    Al-Ketan, Oraib
    Baobaid, Nada
    Khan, Kamran
    Abu Al-Rub, Rashid K.
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2019, VOL 8, 2019,
  • [35] Heat transfer study on finned tube heat exchanger using CFD
    Rajeshkumar, M.
    Logesh, K.
    Thangaraj, M.
    Govindan, S.
    INTERNATIONAL JOURNAL OF AMBIENT ENERGY, 2021, 42 (03) : 239 - 243
  • [36] EXPERIMENTAL-DETERMINATION OF VOLUMETRIC HEAT-TRANSFER COEFFICIENT IN A ROTARY DRYER
    ALVAREZ, PI
    SHENE, C
    DRYING TECHNOLOGY, 1994, 12 (07) : 1605 - 1627
  • [37] Modeling for heat transfer coefficient in indirect-heating tube rotary dryer
    Li, X. (lixuanyou@sina.com), 2013, Chinese Society of Agricultural Engineering (29):
  • [38] Heat and mass transfer characteristics of filamentous particles in transverse section of rotary dryer
    Yuan, Zhulin, 1600, Southeast University (44):
  • [39] Characterization of heat and mass transfer from textiles inside the rotating drum of a clothes dryer
    Yu, Xinchen
    Chen, Hui
    Liu, Yingwen
    APPLIED THERMAL ENGINEERING, 2025, 268
  • [40] A Preliminary Study of Hydrodynamics and Heat Transfer in a Bubbling Fluidized Bed containing Sand Particle using CFD
    Perrone, Diego
    Amelio, Mario
    69TH CONFERENCE OF THE ITALIAN THERMAL ENGINEERING ASSOCIATION, ATI 2014, 2015, 81 : 1041 - 1054
12345