Effects of Induction Heating Conditions on Ni-Al Based Intermetallic Compound Coating

被引：3

作者：

Lee, Han-Young ^{[1
]}

Kim, Tae-Jun ^{[2
]}

Cho, Yong-Jae ^{[2
]}

机构：

[1] Keimyung Univ, Dept Adv Mat Engn, Taegu 704702, South Korea

[2] Keimyung Univ, Grad Sch, Dept Mat Engn, Taegu 704702, South Korea

来源：

KOREAN JOURNAL OF METALS AND MATERIALS | 2010年 / 48卷 / 02期

关键词：

intermetallics; coating; microstructure; scanning electron microscopy/X-ray diffraction; induction heating; DUCTILE CAST-IRON;

D O I：

10.3365/KJMM.2010.48.02.141

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

An Ni-Al intermetallic coating has been produced by induction heating on mild steel. The effect of the induction heating conditions on the microstructure of the coating has been investigated. The reaction synthesis of the intermetallic compounds was promoted while increasing the heating rate and the holding time at reaction temperature. Especially, an NiAl phase corresponding to the initial composition of mixed powder was predominantly formed. However, the synthesis at low reaction temperatures occurred by solid state diffusion during the holding time and an Fe-Al reaction layer was formed at the interface with the substrate, regardless of the heating rate. The combustion synthesis of the intermetallic compound occurred at a temperature higher than 1023 K and resulted in an almost single phase NiAl structure.

引用

页码：141 / 147

页数：7

共 50 条

[31] Synthesis of intermetallic compound in isochronal heating of Al/Ni powder mixture and its forming
Yuasa, Eiji
Yamaguchi, Kosuke
Kondou, Katsuyoshi
Aizawa, Tatsuhiko
Funtai Oyobi Fummatsu Yakin/Journal of the Japan Society of Powder and Powder Metallurgy, 2002, 49 (01): : 52 - 57
[32] Effects of geometry and intermetallic bonding on the mechanical response, spalling and fragmentation of Ni-Al laminates
Vitali, Efrem
Wei, Chung-Ting
Benson, David J.
Meyers, Marc A.
ACTA MATERIALIA, 2011, 59 (15) : 5869 - 5880
[33] Reactive sintering behavior of intermetallic compounds in Ni-Al system
Inoue, Masahiro
Suganuma, Katsuaki
Keikinzoku/Journal of Japan Institute of Light Metals, 1994, 44 (11): : 658 - 662
[34] Formation of a Ni3Al Intermetallic Coating by Cold Spray Deposition of a Ni-Al Powder Mixture Mechanically Processed in a Planetary Mill
Chesnokov, A. E.
Smirnov, A. V.
Drozdov, V. O.
Skorokhod, K. A.
TECHNICAL PHYSICS LETTERS, 2023, 49 (04) : 33 - 36
[35] Cavitation erosion and corrosion behavior of Ni-Al intermetallic coatings
Chang, JT
Yeh, CH
He, JL
Chen, KC
WEAR, 2003, 255 : 162 - 169
[36] Effect of Reactive SPS on the Microstructure and Properties of a Dual-Phase Ni-Al Intermetallic Compound and Ni-Al-TiB2 Composite
Hyjek, Pawel
Sulima, Iwona
Malczewski, Piotr
Bryla, Krzysztof
Jaworska, Lucyna
MATERIALS, 2020, 13 (24) : 1 - 20
[37] Interfacial formation of intermetallic Ni-Al-Ti systems formed by induction heating
Riyadi, Tri Widodo Besar
Siswanto, Waluyo Adi
Zhu, Xiaomeng
FRONTIERS IN MECHANICAL ENGINEERING-SWITZERLAND, 2022, 8
[38] In-situ reactive fabrication and effect of phosphorus on microstructure evolution of Ni/Ni-Al intermetallic composite coating by laser cladding
Liu, Kun
Li, Yajiang
Wang, Juan
MATERIALS & DESIGN, 2016, 105 : 171 - 178
[39] DEVELOPMENT OF Ni-Al AND Ni-Al-Fe INTERMETALLIC COATINGS ON CARBON TOOL STEELS
Salehi, M.
Shamanian, M.
Ashrafizadeh, F.
SURFACE ENGINEERING, 1997, 13 (06) : 505 - 508
[40] Coating in the Ni-Al system using the SHS method
Shulpekov, A. M.
Gabbasov, R. M.
6TH INTERNATIONAL CONGRESS ENERGY FLUXES AND RADIATION EFFECTS, 2018, 1115

← 1 2 3 4 5 →