Experimental and Theoretical Evaluation of Stiffness Properties of Fused Deposition Modeling Parts

被引：0

作者：

Osborn, T. ^{[1
]}

Zhou, E. ^{[1
]}

Gerzeski, R. ^{[2
]}

Mollenhauer, D. ^{[2
]}

Tandon, G. P. ^{[1
]}

Whitney, T. J. ^{[3
]}

Iarve, E. V. ^{[1
]}

机构：

[1] Univ Dayton, Res Inst, 300 Coll Pk, Dayton, OH 45469 USA

[2] Air Force Res Lab, Wright Patterson AFB, OH USA

[3] Univ Dayton, Dayton, OH 45469 USA

来源：

PROCEEDINGS OF THE AMERICAN SOCIETY FOR COMPOSITES: THIRTIETH TECHNICAL CONFERENCE | 2015年

关键词：

COMPOSITES;

D O I：

暂无

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

An experimental and theoretical investigation of mechanical properties of the ULTEM 9085 FDM printed unidirectional parts was performed. The mechanical property prediction was performed based on three-dimensional homogenization methodology and did not involve any empirical coefficients. The only calibrated parameter was the insitu elastic modulus of the FDM roads. The influence of the shape of the air gap between the roads was investigated. Best agreement for the predicted and measured transverse modulus was achieved for the equilateral shape of the gap. Good agreement also was observed for shear modulus.

引用

页码：2589 / 2598

页数：10

共 50 条

[1] Theoretical-experimental evaluation of different biomaterials for parts obtaining by fused deposition modeling
Ortega, Z.
Aleman, M. E.
Benitez, A. N.
Monzon, M. D.
MEASUREMENT, 2016, 89 : 137 - 144
[2] Experimental and Theoretical Investigation of the Mechanical Properties of PHBH Biopolymer Parts Produced by Fused Deposition Modeling
Nobili, Andrea
Signorini, Cesare
Volpini, Valentina
MACROMOLECULAR SYMPOSIA, 2022, 405 (01)
[3] EXPERIMENTAL DETERMINATION OF THE TENSILE STRENGTH OF FUSED DEPOSITION MODELING PARTS
Savvakis, K.
Petousis, M.
Vairis, A.
Vidakis, N.
Bikmeyev, A. T.
PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2014, VOL 14, 2015,
[4] Effects of material properties on warpage in fused deposition modeling parts
Emily R. Fitzharris
Narumi Watanabe
David W. Rosen
Meisha L. Shofner
The International Journal of Advanced Manufacturing Technology, 2018, 95 : 2059 - 2070
[5] Effects of material properties on warpage in fused deposition modeling parts
Shofner, Meisha L. (meisha.shofner@mse.gatech.edu), 1600, Springer London (95): : 5 - 8
[6] Effects of material properties on warpage in fused deposition modeling parts
Fitzharris, Emily R.
Watanabe, Narumi
Rosen, David W.
Shofner, Meisha L.
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 95 (5-8): : 2059 - 2070
[7] Experimental and Numerical Investigation of the Flexural Behavior of Fused Deposition Modeling Parts
Gokulakrishnan, Jothibabu
Kumar, Gurunathan Saravana
ADVANCES IN ADDITIVE MANUFACTURING AND JOINING, AIMTDR 2018, 2020, : 347 - 355
[8] Mechanical properties analysis of polyetherimide parts fabricated by fused deposition modeling
Jiang, Shenglong
Liao, Guangxin
Xu, Dingding
Liu, Fenghua
Li, Wen
Cheng, Yuchuan
Li, Zhixiang
Xu, Gaojie
HIGH PERFORMANCE POLYMERS, 2019, 31 (01) : 97 - 106
[9] Mechanical properties of thermoplastic parts produced by fused deposition modeling: a review
Bakir, Ali Alperen
Atik, Resul
Ozerinc, Sezer
RAPID PROTOTYPING JOURNAL, 2021, 27 (03) : 537 - 561
[10] Influence of fused deposition modeling parameters on the mechanical properties of ABS parts
Vicente, Carlos M. S.
Martins, Tomas S.
Leite, Marco
Ribeiro, Antonio
Reis, Luis
POLYMERS FOR ADVANCED TECHNOLOGIES, 2020, 31 (03) : 501 - 507

← 1 2 3 4 5 →