Development of a Methodology for Structural and Mechanical Characterization of Extended Sheets Made from Stainless Steels

被引：2
|
作者：
de Faria, Geraldo Lucio [1 ]
Godefroid, Leonardo Barbosa [1 ]
Menezes, Victor Silva [1 ]
机构：
[1] Univ Fed Ouro Preto, Ouro Preto, MG, Brazil
来源：
MATERIALS RESEARCH-IBERO-AMERICAN JOURNAL OF MATERIALS | 2015年 / 18卷
关键词：
extended sheets; stainless steels; microstructural and mechanical characterization; MICROSTRUCTURE;
D O I：
10.1590/1516-1439.347614
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Extended sheets are produced by a pressure cutting process to transform common sheets in expanded metal. These sheets are usually made of carbon steel, but due to their corrosion susceptible, studies have been developed with the aim to evaluate the viability of replacing these common steels by stainless steels. This study proposed an experimental method to characterize structural and mechanically samples of stainless steel extended sheets (410D, 444A, 439 and 304A) and a 1010 carbon steel sheet thicker than the others. This study has a practical importance because nowadays there are not standardized procedures to do this kind of evaluation. The obtained results showed that the methodology was effective for the proposed objective and that the expanded sheets made of stainless steels have a better performance in terms of mechanical strength compared to the 1010 steel sheet.
引用
收藏
页码：76 / 82
页数：7
相关论文
共 50 条
  • [21] Evaluation of the mechanical properties and deformability of metal-based composite sheets made of thin stainless-steel sheets and carbon fiber reinforced plastics
    Yuki Shibuya
    Jingwei Zhang
    Yuji Sato
    Jun Yanagimoto
    International Journal of Material Forming, 2022, 15
  • [22] Mechanical and Dynamic Mechanical Properties of Sheets Made from Micro-Fibrillated Cellulose and Cationic Polyacrylamide
    Sakaemura, Takushi
    Yamauchi, Tatsuo
    SEN-I GAKKAISHI, 2014, 70 (04) : 84 - 87
  • [23] Small punch test: A non destructive technique for mechanical characterization of structural steels
    Advanced Materials and Processes Research Institute , Bhopal 462 026, India
    不详
    不详
    J Struct Eng, 2009, 1 (49-53): : 49 - 53
  • [24] Development of a new methodology for estimating the CTOD of structural steels using the small punch test
    Garcia, T. E.
    Rodriguez, C.
    Belzunce, F. J.
    Cuesta, I. I.
    ENGINEERING FAILURE ANALYSIS, 2015, 50 : 88 - 99
  • [25] MECHANICAL BEHAVIOR OF OVERLAP-WELDED OF DISSIMILAR STEELS (STRUCTURAL-STAINLESS) UNDER MONOTONIC LOAD
    Garcia Fuentes, Andres L.
    Bazan, Pierre
    Centeno, Leiry
    Ramos, Magaly
    Velazquez del Rosario, Alberto
    ADVANCED MATERIALS AND PROCESSES II, PTS 1-3, 2012, 557-559 : 1268 - +
  • [26] Development of lean duplex stainless steels (LOSS) with superior mechanical and corrosion properties on laboratory scale
    Srikanth, S.
    Saravanan, P.
    Govindarajan, P.
    Sisodia, S.
    Ravi, K.
    CENTURY OF STAINLESS STEELS, 2013, 794 : 714 - +
  • [27] DEVELOPMENT OF TECHNOLOGY FOR THE PROCESSING OF MAN-MADE WASTE DURING THE SMELTING OF HIGH-QUALITY STAINLESS STEELS
    Baryshev, E. E.
    JOURNAL OF MINING INSTITUTE, 2005, 166 : 34 - 35
  • [28] AN INVERSE PROBLEM FOR THE MECHANICAL CHARACTERIZATION OF STEELS FROM THE TAYLOR TEST
    Hernandez, C.
    Maranon, A.
    Ashcroft, I. A.
    Casas-Rodriguez, J. P.
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION (IMECE 2010), VOL 9, 2012, : 501 - 506
  • [29] The development of alumina-forming austenitic stainless steels for high-temperature structural use
    Brady, M. P.
    Yamamoto, Y.
    Santella, M. L.
    Maziasz, P. J.
    Pint, B. A.
    Liu, C. T.
    Lu, Z. P.
    Bei, H.
    JOM, 2008, 60 (07) : 12 - 18
  • [30] The development of alumina-forming austenitic stainless steels for high-temperature structural use
    M. P. Brady
    Y. Yamamoto
    M. L. Santella
    P. J. Maziasz
    B. A. Pint
    C. T. Liu
    Z. P. Lu
    H. Bei
    JOM, 2008, 60
12345