Friction-stir welding of ultra-fine grained sheets of Al-Mg-Sc-Zr alloy

被引：52

作者：

Malopheyev, S. ^{[1
]}

Mironov, S. ^{[2
]}

Kulitskiy, V. ^{[1
]}

Kaibyshev, R. ^{[1
]}

机构：

[1] Belgorod State Univ, Lab Mech Properties Nanoscale Mat & Superalloys, Belgorod 308015, Russia

[2] Tohoku Univ, Grad Sch Engn, Dept Mat Proc, Sendai, Miyagi 9808579, Japan

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2015年 / 624卷

关键词：

Aluminum alloys; Friction stir welding; Thermo-mechanical processing; Equal-channel angular pressing; Ultra-fine grained microstructure; STRAIN RATE SUPERPLASTICITY; ALUMINUM-ALLOYS; OXIDE ARRAY; BEHAVIOR; REFINEMENT; MICROSTRUCTURE; PRECIPITATION; DEFORMATION; TEMPERATURE; AL3SC;

D O I：

10.1016/j.msea.2014.11.079

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

The effect of friction-stir welding (FSW) on the microstructure and mechanical properties of Al-5.4Mg-0.2Sc-0.1Zr sheets with ultra-fine grained (UFG) microstructure was studied. The UFG material was produced by equal-channel angular pressing (ECAP) followed by either hot or cold rolling. FSW was found to be very effective for preservation of the UFG microstructure as well as the constituent coherent nano-scale dispersoids in the welded material. Despite the preservation effect, however, essential material softening was observed in the weld zone. This observation was attributed to recrystallization presumably occurring during FSW. The joint efficiency for the yield strength of the obtained friction-stir welds was found to be 85% in the hot rolled condition and only 57% in the cold rolled state. The relatively low joint efficiency was attributed to the recrystallization softening as well as to the formation of a "zigzag line" defect in the stir zone. (C) 2014 Elsevier B.V. All rights reserved.

引用

页码：132 / 139

页数：8

共 50 条

[21] Microstructure evolution and strengthening mechanisms of an additive friction stir deposited multi-layer Al-Mg-Sc-Zr alloy
Zhang, Mingtao
Jiang, Tao
Xie, Yunfei
Feng, Xiangnan
Su, Yu
Shen, Zhikang
Sun, Zhonggang
Xu, Yaxin
Li, Wenya
JOURNAL OF ALLOYS AND COMPOUNDS, 2024, 1004
[22] Microstructure evolution and strengthening mechanisms in friction-stir welded Al-Mg-Sc alloy
Vysotskiy, I.
Zhemchuzhnikova, D.
Malopheyev, S.
Mironov, S.
Kaibyshev, R.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 770
[23] Tensile and fatigue properties of Al-Mg-Sc-Zr alloy fine-grained by equal-channel angular pressing
Washikita, A
Kitagawa, K
Kopylov, VI
Vinogradov, A
ULTRAFINE GRAINED MATERIALS II, 2002, : 341 - 350
[24] Thermal stability of ultra-fine grained 2024 aluminum alloy prepared by friction stir processing
Sun, Meina
Wang, Kuaishe
Xu, Ruiqi
Wang, Wen
Hao, Yaxin
Li, Yao
Xiyou Jinshu/Chinese Journal of Rare Metals, 2014, 38 (05): : 780 - 785
[25] Properties and Microstructure of Novel Al-Mg-Sc-Zr Alloy
Guo Q.
Xu G.
Huang J.
Yin Z.
Deng Y.
Xiyou Jinshu/Chinese Journal of Rare Metals, 2019, 43 (03): : 255 - 264
[26] Elongation increase in ultra-fine grained Al-Fe-Si alloy sheets
Kim, HW
Kang, SB
Tsuji, N
Minamino, Y
ACTA MATERIALIA, 2005, 53 (06) : 1737 - 1749
[27] Deformation mechanisms in an ultra-fine grained Al alloy
Sabirov, Ilchat
Barnett, Matthew R.
Estrin, Yuri
Timokhina, Ilana
Hodgson, Peter D.
INTERNATIONAL JOURNAL OF MATERIALS RESEARCH, 2009, 100 (12) : 1679 - 1685
[28] Achieving ultra-fine grains in AZ61 Mg alloy by friction stir processing
Du, Xinghao
Zhang, Erlin
Wu, Baolin
INTERNATIONAL JOURNAL OF MATERIALS RESEARCH, 2008, 99 (12) : 1375 - 1378
[29] Thermal stability of friction stir processed ultrafine grained Al-Mg-Sc alloy
Kumar, N.
Mishra, R. S.
MATERIALS CHARACTERIZATION, 2012, 74 : 1 - 10
[30] Tensile property of Al-Mg-Sc-Zr alloy at cryogenic temperature
Zhao, W. T.
Yan, D. S.
Li, X. Y.
Rong, L. J.
Li, Y. Y.
ADVANCES IN CRYOGENIC ENGINEERING, VOL 52A & 52B, 2006, 824 : 169 - +

← 1 2 3 4 5 →