Room temperature Young's modulus, shear modulus, Poisson's ratio and hardness of PbTe-PbS thermoelectric materials

被引：93

作者：

Ni, Jennifer E. ^{[1
]}

Case, Eldon D. ^{[1
]}

Khabir, Kristen N. ^{[1
]}

Stewart, Ryan C. ^{[1
]}

Wu, Chun-I. ^{[2
]}

Hogan, Timothy P. ^{[2
]}

Timm, Edward J. ^{[3
]}

Girard, Steven N. ^{[4
]}

Kanatzidis, Mercouri G. ^{[4
]}

机构：

[1] Michigan State Univ, Dept Chem Engn & Mat Sci, E Lansing, MI 48824 USA

[2] Michigan State Univ, Dept Elect & Comp Engn, E Lansing, MI 48824 USA

[3] Michigan State Univ, Dept Mech Engn, E Lansing, MI 48824 USA

[4] Northwestern Univ, Dept Chem, Evanston, IL USA

来源：

MATERIALS SCIENCE AND ENGINEERING B-ADVANCED FUNCTIONAL SOLID-STATE MATERIALS | 2010年 / 170卷 / 1-3期

关键词：

Thermoelectric; Lead telluride; Powder processing; Elasticity; Hardness; MECHANICAL-PROPERTIES; GRAIN-SIZE; ELASTIC-MODULI; FRACTURE-TOUGHNESS; CRACK INITIATION; INDENTATION; MICROHARDNESS; NANOINDENTATION; AGPBMSBTE2+M; MICROCRACKS;

D O I：

10.1016/j.mseb.2010.02.026

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Two-phase PbTe-PbS materials, in which PbS is a nanostructured phase, are promising thermoelectric materials for the direct conversion of heat energy into electricity. In this study, a Vickers indentation mean hardness of 1.18 +/- 0.09 GPa was measured for hot pressed specimens Pb0.95Sn0.05Te-PbS 8% while the mean hardness of cast specimens was 0.68 +/- 0.07 GPa. The mean fracture toughness of the not pressed specimens was estimated as 0.35 +/- 0.04 MPa m(1/2) via Vickers indentation. Resonant Ultrasound Spectroscopy (RUS) measurements on hot pressed specimens gave mean values of Young's modulus, shear modulus and Poisson's ratio of 53.1 GPa, 21.4 GPa and 0.245, respectively while for the cast specimens the Young's and shear moduli were about 10% lower than for the hot pressed, with a mean value of Poisson's ratio of 0.245. The differences between the hardness and elastic moduli values for the cast and hot pressed specimens are discussed. (C) 2010 Elsevier B.V. All rights reserved.

引用

页码：58 / 66

页数：9

共 50 条

[21] Young's modulus and Poisson's ratio of the deformable cement adhesives
Karpiesiuk, Jacek
Chyzy, Tadeusz
SCIENCE AND ENGINEERING OF COMPOSITE MATERIALS, 2020, 27 (01) : 299 - 307
[22] Neural network estimates Poisson's ratio, Young's modulus
Shahriari, Shirin
Pazuki, Gholamreza
Al-Anazi, Bandar Duraya
OIL & GAS JOURNAL, 2010, 108 (19) : 47 - 50
[23] What is the Young's modulus and the Poisson ratio of vulcanized rubber?
Wie groß sind der E-Modul und die Querkontraktionszahl von Gummi?
Baaser, H. (Herbert.Baaser@Freudenberg.de), 2013, Huthig GmbH (66): : 11 - 12
[24] What is the Young's modulus and the Poisson ratio of vulcanized rubber?
Baaser, Herbert
KGK-KAUTSCHUK GUMMI KUNSTSTOFFE, 2013, 66 (11-12): : 25 - 28
[25] Young's modulus and Poisson ratio of composite materials: Influence of wet and dry storage
Lourenco, Ana Lucia
De Jager, Niek
Prochnow, Catina
Milbrandt Dutra, Danilo Antonio
Kleverlaan, Cornelis J.
DENTAL MATERIALS JOURNAL, 2020, 39 (04) : 657 - 663
[26] Anisotropy of Young's Modulus and Microhardness of PbTe
Lusakowska, E.
Adamiak, S.
Minikayev, R.
Skupinski, P.
Szczerbakow, A.
Szuszkiewicz, W.
ACTA PHYSICA POLONICA A, 2018, 134 (04) : 941 - 943
[27] Estimating Young's modulus and Poisson's ratio by instrumented indentation test
Zorzi, J. E.
Perottoni, C. A.
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2013, 574 : 25 - 30
[28] Predictions of Young's modulus and negative Poisson's ratio of auxetic foams
Lu, Zi-Xing
Liu, Qiang
Yang, Zhen-Yu
PHYSICA STATUS SOLIDI B-BASIC SOLID STATE PHYSICS, 2011, 248 (01): : 167 - 174
[29] Novel structure with negative Poisson's ratio and enhanced Young's modulus
Lu, Zi-Xing
Li, Xiang
Yang, Zhen-Yu
Xie, Fan
COMPOSITE STRUCTURES, 2016, 138 : 243 - 252
[30] The elastic properties of cancerous skin: Poisson's ratio and Young's modulus
Tilleman, TR
Tilleman, MM
Neumann, MHA
ISRAEL MEDICAL ASSOCIATION JOURNAL, 2004, 6 (12): : 753 - 755

← 1 2 3 4 5 →