Chemical mechanical polishing using mixed abrasive slurries

被引：54
|
作者：
Jindal, A [1 ]
Hegde, S
Babu, SV
机构：
[1] Clarkson Univ, Dept Chem Engn, Potsdam, NY 13699 USA
[2] Clarkson Univ, Ctr Adv Mat Proc, Potsdam, NY 13699 USA
来源：
ELECTROCHEMICAL AND SOLID STATE LETTERS | 2002年 / 5卷 / 07期
关键词：
D O I：
10.1149/1.1479297
中图分类号：
O646 [电化学、电解、磁化学];
学科分类号：
081704 ;
摘要：
Chemical mechanical polishing (CMP) of metal and dielectric films was performed using mixed abrasive slurries (MAS). MAS containing alumina and silica particles dispersed in deionized water were evaluated as second step slurries for Cu damascene polishing. It was demonstrated that MAS with proper selection of constituents and composition of abrasive particles can yield desired slurry/CMP characteristics. Based on the results of transmission electron microscope and particle size analysis of the abrasives in these MAS, possible reasons for the improved CMP performance are discussed. (C) 2002 The Electrochemical Society.
引用
收藏
页码：G48 / G50
页数：3
相关论文
共 50 条
  • [31] A study on the chemical mechanical polishing of oxide film using a zirconia (ZrO2)-mixed abrasive slurry (MAS)
    Park, Sung-Woo
    Seo, Yong-Jin
    Lee, Woo-Sun
    MICROELECTRONIC ENGINEERING, 2008, 85 (04) : 682 - 688
  • [32] Effect of particle size of chemical mechanical polishing slurries for enhanced polishing with minimal defects
    Basim, GB
    Adler, JJ
    Mahajan, U
    Singh, RK
    Moudgil, BM
    JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 2000, 147 (09) : 3523 - 3528
  • [33] A model of pad-abrasive interactions in chemical mechanical polishing
    Paul, Ed
    Horn, John
    Li, Ying
    Babu, S. V.
    ELECTROCHEMICAL AND SOLID STATE LETTERS, 2007, 10 (04) : H131 - H133
  • [34] Chemical mechanical polishing for silicon wafer by composite abrasive slurry
    Key Laboratory of Mechanical Manufacture and Automation Ministry of Education, Zhejiang University of Technology, Hangzhou 310032, China
    Guangxue Jingmi Gongcheng, 2009, 7 (1587-1593):
  • [35] Shear thickening and shear-induced agglomeration of chemical mechanical polishing slurries using electrolytes
    Nathan C. Crawford
    Benjamin Yohe
    S. Kim
    R. Williams
    David Boldridge
    Matthew W. Liberatore
    Rheologica Acta, 2013, 52 : 499 - 513
  • [36] Modeling the effect of bumpy abrasive particles on chemical mechanical polishing
    Mazaheri, AR
    Ahmadi, G
    JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 2002, 149 (07) : G370 - G375
  • [37] Shear thickening of chemical mechanical polishing slurries under high shear
    Nathan C. Crawford
    S. Kim R. Williams
    David Boldridge
    Matthew W. Liberatore
    Rheologica Acta, 2012, 51 : 637 - 647
  • [38] Shear thickening and changes in particle structure of chemical mechanical polishing slurries
    Crawford, Nathan
    Liberatore, Matthew
    Williams, S. Kim R.
    Boldridge, David
    ABSTRACTS OF PAPERS OF THE AMERICAN CHEMICAL SOCIETY, 2011, 242
  • [39] Stabilization of alumina slurries in presence of oxidizers for tungsten chemical mechanical polishing
    Palla, BJ
    Shah, DO
    Bielmann, M
    Singh, RK
    TWENTY THIRD IEEE/CPMT INTERNATIONAL ELECTRONICS MANUFACTURING TECHNOLOGY SYMPOSIUM, 1998, : 155 - 163
  • [40] Evaluation of commercialized slurries and pads for polymer CMP (chemical mechanical polishing)
    Zhang, F
    Wake, RW
    Cook, L
    Busnaina, AA
    CHEMICAL MECHANICAL PLANARIZATION IN INTEGRATED CIRCUIT DEVICE MANUFACTURING, 1998, 98 (07): : 246 - 254
12345