Characteristics of Induced Discharge on a Polymer Insulator Surface under Electro-wetting Conditions

被引:14
|
作者
Liu, Yong [1 ,2 ,3 ]
Du, B. X. [3 ]
Farzaneh, Masoud [1 ,2 ]
机构
[1] Univ Quebec Chicoutimi, NSERC Hydro Quebec UQAC Ind Chair Atmospher Icing, Chicoutimi, PQ G7H 2B1, Canada
[2] Univ Quebec Chicoutimi, Canada Res Chair Engn Power Network Atmospher Ici, Chicoutimi, PQ G7H 2B1, Canada
[3] Tianjin Univ, Sch Elect Engn & Automat, Minist Educ, Key Lab Smart Grid, Tianjin 300072, Peoples R China
关键词
Polymer insulator; electro-wetting condition; AC/DC operating voltage; water droplet deposits; precipitation parameters; surface discharge; surface flashover; FLASHOVER PERFORMANCE; OUTDOOR INSULATORS; FIELD COMPUTATION; LOCAL DISCHARGE; ARC PROPAGATION; MECHANISM; PARAMETERS; ENERGY;
D O I
10.1109/TDEI.2015.005166
中图分类号
TM [电工技术]; TN [电子技术、通信技术];
学科分类号
0808 ; 0809 ;
摘要
In this paper, laboratory experiments were conducted to investigate the precipitation characteristics and induced surface discharge on polymer insulator specimens under electro-wetting conditions simulated by artificial fog-wetting conditions at different operating voltages. Based on image processing methods, quantitative analysis was carried out on precipitation parameters to obtain the deposited amount, relative distribution area, statistics of droplet size distribution and distributed droplet box dimension in relation with the duration of precipitations and operating voltages. Also, the onset voltage of surface discharge and flashover voltage were measured for the purpose of establishing the influence of the obtained precipitation parameters on the surface discharge. It was found that the precipitation process is in a dynamic balance between fog deposition and droplet evaporation, and is significantly affected by the type and level of operating voltage. Operating voltage increase results in a relatively lower deposit amount and distributing area of water droplets. There are further reduced when the precipitating duration is increased at higher voltage level. The small-size (< 1 mm) droplets are dominating on the specimen surface for all the investigated conditions. The large-size (>= 2 mm) droplets increase with increasing AC operating voltage, but do not appear significantly under high +/- DC operating voltage. When precipitation duration is increased, box dimension of droplet distribution under non-and low- operating voltage shows tendency to increase, but tendency to decrease under high operating voltage. Finally, a relationship between the onset voltage of surface discharge, the flashover voltage and the droplet distribution parameters was established, showing that the increasing precipitation regularity of water droplets on the polymer insulator specimen surface can induce more likely occurrence of surface discharge, even flashover.
引用
收藏
页码:2958 / 2967
页数:10
相关论文
共 50 条
  • [31] Wetting deformation characteristics of intact loess under true triaxial conditions
    Fang Jin-jin
    Feng Yi-xin
    Yu Yong-qiang
    Li Zhen
    Lin Zhi-bin
    ROCK AND SOIL MECHANICS, 2020, 41 (04) : 1235 - 1246
  • [32] Surface discharge of silicone rubber under polluted conditions
    Chen, Y
    Liang, XD
    Fang, XD
    Guan, ZC
    Zhang, RY
    JOINT CONFERENCE OF 96' AICDEI / 4T-JCCEID, 1996, : 275 - 278
  • [33] EFFECTIVE WETTING AND DEWETTING OF A SUPERHYDROPHOBIC SURFACE UNDER DYNAMIC THERMAL CONDITIONS
    O'Keeffe, Niall
    Eason, Cormac
    Enright, Ryan
    Davies, Mark
    HT2009: PROCEEDINGS OF THE ASME SUMMER HEAT TRANSFER, VOL 3, 2009, : 517 - 526
  • [34] SUBSTRATE WETTING UNDER THE CONDITIONS OF DROP FREE FALLING ON A HEATED SURFACE
    Batischeva, Ksenia A.
    Feoktistov, Dmitriy V.
    Misyura, Sergey Y.
    SMART GRIDS 2015, 2015, 37
  • [35] Transient discharge characteristics of insulator short-circuit under high voltage
    Qi, Shancheng
    Chang, Shuaibing
    Cao, Lilu
    ALEXANDRIA ENGINEERING JOURNAL, 2021, 60 (06) : 5175 - 5181
  • [36] Decomposition Characteristics of SF6 under creeping discharge on solid insulator
    Ding, Weidong
    Wang, Jiachen
    Gu, Yue
    Li, Guojun
    2016 INTERNATIONAL CONFERENCE ON CONDITION MONITORING AND DIAGNOSIS (CMD), 2016, : 701 - U1140
  • [37] Study of thermal stresses induced surface damage under growing plasma channel in electro-discharge machining
    Kumar, Panda Deepak
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 202 (1-3) : 86 - 95
  • [38] Characterization of Leakage Current on the Surface of Porcelain Insulator under Contaminated Conditions
    Terrab, Hocine
    El-Hag, Ayman
    Bayadi, Abdelhafid
    2015 4TH INTERNATIONAL CONFERENCE ON ELECTRIC POWER AND ENERGY CONVERSION SYSTEMS (EPECS), 2015,
  • [39] Effect of insulator shape on surface discharges and flashover under polluted conditions
    Boudissa, R
    Djafri, S
    Haddad, A
    Belaicha, R
    Bearsch, R
    IEEE TRANSACTIONS ON DIELECTRICS AND ELECTRICAL INSULATION, 2005, 12 (03) : 429 - 437
  • [40] On erosion characteristics of compacted loess during wetting procedure under laboratory conditions
    Zhihua Yao
    Jie Lian
    Jun Zhang
    Maojiang Zhu
    Environmental Earth Sciences, 2019, 78