Cavitating flow around a scaled-down model of guide vanes of a high-pressure turbine

被引:33
|
作者
Timoshevskiy, Mikhail V. [1 ,2 ]
Churkin, Sergey A. [1 ,2 ]
Kravtsova, Aleksandra Yu. [1 ,2 ]
Pervunin, Konstantin S. [1 ,2 ]
Markovich, Dmitriy M. [1 ,2 ,3 ]
Hanjalic, Kemal [1 ,4 ]
机构
[1] Novosibirsk State Univ, Dept Sci Res, Novosibirsk 630090, Russia
[2] Russian Acad Sci, Kutateladze Inst Thermophys, Siberian Branch, Novosibirsk 630090, Russia
[3] Tomsk Polytech Univ, Inst Power Engn, Tomsk 634050, Russia
[4] Delft Univ Technol, Dept Chem Engn, NL-2628 BL Delft, Netherlands
基金
俄罗斯科学基金会;
关键词
Cavitation; Attached/cloud cavities; System/intrinsic instabilities; Asymmetric cavity length oscillations; Cross instability; Guide vane; NACA0015; High-speed visualization; PIV; EDGE FLAT-PLATE; CLOUD CAVITATION; BOUNDARY-LAYER; INSTABILITY;
D O I
10.1016/j.ijmultiphaseflow.2015.09.014
中图分类号
O3 [力学];
学科分类号
08 ; 0801 ;
摘要
We studied cavitating flow over the suction side of two symmetric 2D foils - a NACA0015 hydrofoil and a scaled-down model of high-pressure hydroturbine guide vanes (GV) - in different cavitation regimes at several attack angles. High-speed imaging was used to analyze spatial patterns and time dynamics of the gas-vapor cavities, as well as for evaluating the characteristic integral parameters. A PIV technique was applied to measure the velocity fields and its fluctuations, which were compared for both foils and with the data measured in the non-cavitating flows at the same flow conditions. We compare the dynamics of growth and convection of traveling bubbles at a smaller attack angle and the transition of a sheet cavity pattern to a streaky one at the higher incidence on both foils. For the GV, asymmetric spanwise variations of the sheet cavity length were for the first time visualized for an unsteady regime that is characterized by alternating periodic detachments of clouds between the sidewalls of the test channel and Strouhal number of 0.27. According to numerical calculations by Decaix and Goncalves (2013), this asymmetric behavior is very likely to be governed by the cross instability. Moreover, it was concluded that the existence of the cross instability is independent on the test body shape and its aspect ratio. For single-phase flow and cavitation inception conditions, the PIV measurements revealed the appearance of the second maximum in the fluctuating velocity distributions over the GV profile at the higher incidence angle due to the flow separation from its surface at roughly 71% of the chord length from the foil leading edge. This results in a more intensive turbulent wake past the GV compared to that behind the NACA foil. After the transition to unsteady regimes, both maxima of the fluctuating velocity over the GV vanish, the distributions become more flat and almost coincide for both foils. While at developed cavitation regimes the main flow features and cavitation dynamics do not differ much for the both foils, the detected second maximum of the fluctuating velocity for the GV at the higher attack angle makes this profile less suitable (from the hydrodynamics standpoint) for flow control in practical full-scale conditions, especially at subcavitating and cavitation inception regimes, than the NACA hydrofoil. (C) 2015 Elsevier Ltd. All rights reserved.
引用
收藏
页码:75 / 87
页数:13
相关论文
共 50 条
  • [31] SCALE-ADAPTIVE SIMULATIONS OF HIGH-PRESSURE TURBINE GUIDE VANE
    Wang, Guoliang
    Zhong, Dongdong
    Ge, Ning
    Yang, Rongfei
    PROCEEDINGS OF THE ASME GAS TURBINE INDIA CONFERENCE, 2019, VOL 1, 2020,
  • [32] DESIGN AND MANUFACTURE OF EBC COATED SIC/SIC NOZZLE GUIDE VANES FOR HIGH-PRESSURE TURBINES
    Suess, Fabia
    Schoeffler, Robin
    Friedrich, Lion
    Petersen, Anna
    Vogel, Felix
    Friess, Martin
    Ebach-Stahl, Andrea
    PROCEEDINGS OF ASME TURBO EXPO 2024: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, GT2024, VOL 2, 2024,
  • [33] Turbulent Structure of Cavitating Flow: PIV Measurements over a Model of Guide Vane of Hydraulic Turbine
    Timoshevskiy, M. V.
    Ilyushin, B. B.
    Pervunin, K. S.
    JOURNAL OF ENGINEERING THERMOPHYSICS, 2020, 29 (03) : 407 - 413
  • [34] HEAT TRANSFER COEFFICIENT AND ADIABATIC WALL TEMPERATURE MEASUREMENTS ON A HIGH-PRESSURE TURBINE NOZZLE GUIDE VANES WITH REPRESENTATIVE INLET SWIRL AND TEMPERATURE DISTORTIONS
    Bacci, T.
    Picchi, A.
    Babazzi, G.
    Facchini, B.
    Cubeda, S.
    Hughes, Baker
    PROCEEDINGS OF ASME TURBO EXPO 2022: TURBOMACHINERY TECHNICAL CONFERENCE AND EXPOSITION, GT2022, VOL 6B, 2022,
  • [35] MEASUREMENT OF UNSTEADY AND CAVITATING FLOW IN A MODEL FRANCIS TURBINE OF HIGH SPECIFIC SPEED
    GERICH, R
    RAABE, J
    JOURNAL OF FLUIDS ENGINEERING-TRANSACTIONS OF THE ASME, 1975, 97 (04): : 402 - 411
  • [36] Solid-liquid Two-phase Flow Numerical Simulation around Guide Vanes of Mixed-flow Water Turbine
    Li, Qifei
    Li, Rennian
    Quan, Hui
    Han, Wei
    INTERNATIONAL CONFERENCE ON ADVANCES IN COMPUTATIONAL MODELING AND SIMULATION, 2012, 31 : 87 - 91
  • [37] Improvement of gas-turbine acceleration performance by scheduling variable stator vanes in high-pressure compressors
    Salchow, K
    FORSCHUNG IM INGENIEURWESEN-ENGINEERING RESEARCH, 1997, 63 (05): : 161 - 167
  • [38] Measurement of Surface Changes in a Scaled-Down Landslide Model Using High-Speed Stereo Image Sequences
    Feng, Tiantian
    Mi, Huan
    Scaioni, Marco
    Qiao, Gang
    Lu, Ping
    Wang, Weian
    Tong, Xiaohua
    Li, Rongxing
    PHOTOGRAMMETRIC ENGINEERING AND REMOTE SENSING, 2016, 82 (07): : 547 - 557
  • [39] Influence of endwall profiling on purge flow and mainstream flow in the high-pressure turbine
    Xie B.
    Zhang Y.
    Zhang Z.
    Hangkong Dongli Xuebao/Journal of Aerospace Power, 2023, 38 (09): : 2241 - 2250
  • [40] Design and Manufacture of SiC/SiC Nozzle Guide Vanes With Environmental Barrier Coatings for High-Pressure Turbines
    Suess, Fabia
    Schoeffler, Robin
    Friedrich, Lion
    Petersen, Anna
    Vogel, Felix
    Friess, Martin
    Ebach-Stahl, Andrea
    JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2025, 147 (02):