Process parameters analysis of direct laser sintering and post treatment of porcelain components using Taguchi's method

被引：54
|
作者：
Tian, Xiaoyong [1 ,2 ]
Guenster, Jens [1 ]
Melcher, Joerg [3 ]
Li, Dichen [2 ]
Heinrich, Juergen G. [1 ]
机构：
[1] Tech Univ Clausthal, Dept Ceram Engn, D-38678 Clausthal Zellerfeld, Germany
[2] Xi An Jiao Tong Univ, State Key Lab Mech Mfg Syst Engn, Xian 710049, Peoples R China
[3] German Aerosp Ctr, Inst Composite Struct & Adapt Syst, D-38108 Braunschweig, Germany
来源：
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY | 2009年 / 29卷 / 10期
关键词：
Direct laser sintering; Mechanical properties; Porcelain; Mullite; Structural application; PHOTONIC CRYSTALS; BENDING STRENGTH; PHASE EVOLUTION; FABRICATION;
D O I：
10.1016/j.jeurceramsoc.2008.12.002
中图分类号：
TQ174 [陶瓷工业]; TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The effects of laser sintering parameters (laser power, scan speed and hatching space) and post sintering process (heating rate, sintering temperature and holding time) on the physical and mechanical properties of porcelain components have been investigated. The study has been carried out using the Taguchi's method for the experimental design. In the laser sintering process, lower laser energy density and higher hatching space will increase the final mechanical properties of the porcelain components. A stress relief principle has been put forward to explain the different influence of the factors. The appropriate laser sintering parameters are attained in this paper: laser power 50 W; scan speed 85 mm/s; and hatching space 0.6 mm. Sintering temperature has been determined to be the most important factor in the post sintering process. Appropriate sintering temperature for the laser sintered porcelain bodies is in the range of 1425-1475 degrees C regarding the mechanical properties of the porcelain components. The maximum bending strength, 34.0 +/- 4.9 MPa, is reached. (C) 2008 Elsevier Ltd. All rights reserved.
引用
收藏
页码：1903 / 1915
页数：13
相关论文
共 50 条
  • [21] Optimising process parameters for flip chip stencil printing using Taguchi's method
    Rajkumar, D
    Nguty, T
    Ekere, NN
    TWENTY SIXTH IEEE/CPMT INTERNATIONAL ELECTRONICS MANUFACTURING TECHNOLOGY SYMPOSIUM, PROCEEDINGS, 2000, : 382 - 388
  • [22] Analysis of Process Parameters of Plasma Arc Cutting of Stainless Steel Using Taguchi Method
    Maity, K. P.
    Singh, Vivek
    Bhartiya, Sachin
    MECHANICAL AND AEROSPACE ENGINEERING, PTS 1-7, 2012, 110-116 : 3551 - +
  • [23] Optimization of vacuum casting process parameters using Taguchi method
    Ahmad, Mohd Nazri
    Alkahari, Mohd Rizal
    Basir, Mohamad Faris Mohd
    Maidin, Nurul Ain
    Wahid, Mohammad Khalid
    Ab Rahman, Mohd Hidayat
    Osman, Mohd Hairizal
    PROCEEDINGS OF MECHANICAL ENGINEERING RESEARCH DAY 2018 (MERD), 2018, : 146 - 147
  • [24] Determination of submerged arc Welding process parameters using Taguchi Method and Regression analysis
    Gowthaman, K.
    Saiganesh, J.
    Rajamanikam, C. S.
    2013 INTERNATIONAL CONFERENCE ON ENERGY EFFICIENT TECHNOLOGIES FOR SUSTAINABILITY (ICEETS), 2013,
  • [25] Influence of Operating Parameters on the Reciprocating Sliding Wear of Direct Metal Deposition (DMD) Components Using Taguchi Method
    Naiju, C. D.
    Anil, P. M.
    13TH GLOBAL CONGRESS ON MANUFACTURING AND MANAGEMENT, 2017, 174 : 1016 - 1027
  • [26] STRUCTURAL OPTIMIZATION POST-PROCESS USING TAGUCHI METHOD
    PARK, GJ
    HWANG, WJ
    LEE, WI
    JSME INTERNATIONAL JOURNAL SERIES A-MECHANICS AND MATERIAL ENGINEERING, 1994, 37 (02): : 166 - 172
  • [27] Experimental Investigation of process parameters for rapid prototyping technique (Selective Laser Sintering) to enhance the part quality of prototype by Taguchi method
    Kumar, Nitish
    Kumar, Hemant
    Khurmi, Jagdeep Singh
    3RD INTERNATIONAL CONFERENCE ON INNOVATIONS IN AUTOMATION AND MECHATRONICS ENGINEERING 2016, ICIAME 2016, 2016, 23 : 352 - 360
  • [28] Impact of parameters on the process response: A Taguchi orthogonal analysis for laser engraving
    Kasman, Sefika
    MEASUREMENT, 2013, 46 (08) : 2577 - 2584
  • [29] Optimization of Case Treatment AISI 1022 Timber Screw Process Parameters Using Taguchi Method
    Yang, Chih-Cheng
    Yen, Ching-Yun
    SENSORS AND MATERIALS, 2018, 30 (03) : 489 - 502
  • [30] Robust Parameters Design and Optimization of an Underwater Nd:YAG Laser Microchanneling Process Using the Taguchi Method
    Prakash, S.
    Acherjee, B.
    Kuar, A. S.
    Mitra, S.
    LASERS IN ENGINEERING, 2016, 33 (1-3) : 87 - 102
12345