Shrinkage anisotropy in fiber reinforced injection molded products

被引：13
|
作者：
Jansen, KMB [1 ]
Van Dijk, DJ [1 ]
Freriksen, MJA [1 ]
机构：
[1] Univ Twente, Dept Mech Engn, WBOK, NL-7500 AE Enschede, Netherlands
来源：
POLYMER COMPOSITES | 1998年 / 19卷 / 04期
关键词：
D O I：
10.1002/pc.10105
中图分类号：
TB33 [复合材料];
学科分类号：
摘要：
This paper includes a systematic study of the effect of fiber concentration and molding conditions on fiber orientation and shrinkage in injection molded composites. Closed-form expressions were derived to relate shrinkage and internal stresses to the molding pressure and fiber orientation. The shrinkage predictions were seen to agree well with experimentally measured shrinkages.
引用
收藏
页码：325 / 334
页数：10
相关论文
共 50 条
  • [41] ANISOTROPIC SHRINKAGE OF INJECTION-MOLDED RUBBER
    NAKASHIMA, K
    FUKUTA, H
    MINEKI, M
    JOURNAL OF APPLIED POLYMER SCIENCE, 1973, 17 (03) : 769 - 778
  • [42] Linear shrinkage differences in injection molded parts
    Velarde, DA
    Yeagley, MJ
    PLASTICS ENGINEERING, 2000, 56 (12) : 60 - 64
  • [43] Influence of Fiber Orientation, Temperature and Moisture on the Fatigue Behavior of Injection Molded Fiber Reinforced Thermoplastics
    Gaier, Christian
    Fleischer, Harald
    Guster, Christoph
    Pinter, Gerald
    MATERIALS TESTING-MATERIALS AND COMPONENTS TECHNOLOGY AND APPLICATION, 2010, 52 (7-8): : 534 - 542
  • [44] Effect of Fiber Length on Mechanical Properties of Injection Molded Long-Fiber-Reinforced Thermoplastics
    Kim, Youngbum
    Park, O. Ok
    MACROMOLECULAR RESEARCH, 2020, 28 (05) : 433 - 444
  • [45] Effect of Fiber Length on Mechanical Properties of Injection Molded Long-Fiber-Reinforced Thermoplastics
    Youngbum Kim
    O. Ok Park
    Macromolecular Research, 2020, 28 : 433 - 444
  • [46] Prediction and Validation of Fiber Orientation in short Fiber Reinforced Injection Molded SiCN-ceramics
    Mueller-Koehn, A.
    Ahlhelm, M.
    Moritz, T.
    Michaelis, A.
    Ladisch, St.
    CFI-CERAMIC FORUM INTERNATIONAL, 2014, 91 (3-4): : E63 - E68
  • [47] FIBER ORIENTATION IN INJECTION-COMPRESSION MOLDED SHORT-FIBER-REINFORCED POLYPROPYLENE PARTS
    Huang, Han-Xiong
    Yang, Can
    Li, Kun
    IMECE2009: PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, VOL 14, 2010, : 169 - 176
  • [48] An effective model for fiber breakage prediction of injection-molded long fiber reinforced thermoplastics
    Kang, Junyang
    Huang, Ming
    Zhang, Mengfei
    Zhang, Na
    Song, Gang
    Liu, Yongzhi
    Shi, Xianzhang
    Liu, Chuntai
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2020, 39 (11-12) : 473 - 484
  • [49] On the effect of the fiber orientation on the flexural stiffness of injection molded short fiber reinforced polycarbonate plates
    Neves, NM
    Isdell, G
    Pouzada, AS
    Powell, PC
    POLYMER COMPOSITES, 1998, 19 (05) : 640 - 651
  • [50] Injection-molded natural fiber-reinforced polymer composites–a review
    M. S. Rabbi
    Tansirul Islam
    G. M. Sadiqul Islam
    International Journal of Mechanical and Materials Engineering, 2021, 16
12345