Optimization of 3D printing parameters of Screw Type Extrusion (STE) for ceramics using the Taguchi method

被引：26

作者：

Kim, Namsoo Peter ^{[1
,2
]}

Cho, Diana ^{[2
]}

Zielewski, Matthew ^{[1
,2
]}

机构：

[1] Univ Texas El Paso, Dept Met Mat & Biomed Engn, El Paso, TX 79968 USA

[2] Univ Texas El Paso, Ctr Printing Mat Certificat, El Paso, TX 79968 USA

来源：

CERAMICS INTERNATIONAL | 2019年 / 45卷 / 02期

关键词：

3D printing; Screw Type Extrusion (STE); Clays; Porosity; Biomedical applications; FABRICATION; CHALLENGES;

D O I：

10.1016/j.ceramint.2018.10.152

中图分类号：

TQ174 [陶瓷工业]; TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Minimizing the variation of the discharging volume becomes a critical point to control the 3D printability of non-Newtonian ceramics and precise control of pressure, shear rates, and time-dependent viscosity become important factors. Taguchi method was used to obtain a constant linear-velocity by optimizing the printing parameters: A L9 orthogonal array (OA), magnitude, signal-to-noise (S/N) ratio, and extent of the impact of independent variables, which are water content in material (WC), revolutions per minute (RPM), and diameter of the nozzle tip (TIP). This data is employed to improve the 3D printability and linear-velocity of discharged ceramics. Bowls, pottery, and patterns of 2.5D and 3D structures have been successfully printed in various sizes with ceramic materials under optimal conditions. The Taguchi method optimizes the Screw Type Extrusion (STE) process and provides 3D printing data on precise control of ceramics as biomaterials.

引用

页码：2351 / 2360

页数：10

共 50 条

[21] Analysis of the screw press mouthpiece parameters for 3D extrusion of peat pieces of tubular type
Mikhailov, Aleksandr V.
Fedorov, Aleksandr S.
JOURNAL OF MINING INSTITUTE, 2021, 249 : 351 - 365
[22] A Method to Improve the Fracture Toughness Using 3D Printing by Extrusion Deposition
Gardan, Julien
Makke, Ali
Recho, Naman
21ST EUROPEAN CONFERENCE ON FRACTURE, (ECF21), 2016, 2 : 144 - 151
[23] 3D printed elastomers with superior stretchability and mechanical integrity by parametric optimization of extrusion process using Taguchi Method
Bayati, Abbas
Ahmadi, Mina
Rahmatabadi, Davood
Khodaei, Mohammad
Xiang, Hao
Baniassadi, Majid
Abrinia, Karen
Zolfagharian, Ali
Bodaghi, Mahdi
Baghani, Mostafa
MATERIALS RESEARCH EXPRESS, 2025, 12 (01)
[24] Taguchi optimization of mask stereolithographic 3D printing parameters for tensile strengthening of functionally graded resins
Sharifi, Hanieh
Adib, Ali
Ahmadi, Zohre
Gemikonakli, Eser
Asl, Mehdi Shahedi
INTERNATIONAL JOURNAL OF INTERACTIVE DESIGN AND MANUFACTURING - IJIDEM, 2024, 18 (07): : 4899 - 4910
[25] 3D printing using powder melt extrusion
Boyle, Bret M.
Xiong, Panupoan T.
Mensch, Tara E.
Werder, Timothy J.
Miyake, Garret M.
ADDITIVE MANUFACTURING, 2019, 29
[26] Investigating the Combined Effect of FDM 3D Printing Parameters on Tensile Behavior of ABS Plastic Using Taguchi Method
Hashmi, Wajid Ali
Rehman, Abdul
Lathkar, G. S.
Attar, P. R.
Zubairuddin, M.
JOURNAL OF POLYMER & COMPOSITES, 2024, 12 : S161 - S169
[27] Analysing of Food Printing Parameters of Cartesian Type 3D Printers With Screw Transfer System
Kayak, Gulce
Cetinkaya, Kerim
JOURNAL OF POLYTECHNIC-POLITEKNIK DERGISI, 2018, 21 (03): : 663 - 667
[28] Parametric Optimization of the 3D Printing Process for Dimensional Accuracy of Biopolymer Parts Using the Grey-Taguchi Method
Kumar, Kapil
Singh, Hari
IRANIAN JOURNAL OF SCIENCE AND TECHNOLOGY-TRANSACTIONS OF MECHANICAL ENGINEERING, 2023, 48 (3) : 1101 - 1116
[29] Optimization of 3D printing parameters for BaTiO3 piezoelectric ceramics through design of experiments
Renteria, Anabel
Fontes, Hilda
Diaz, Jorge A.
Regis, Jaime E.
Chavez, Luis A.
Tseng, Tzu-Liang
Liu, Yingtao
Lin, Yirong
MATERIALS RESEARCH EXPRESS, 2019, 6 (08)
[30] Investigation of material extrusion parameters and printing material impacts on wear and friction using the Taguchi method
Aslan, Enes
RAPID PROTOTYPING JOURNAL, 2025,

← 1 2 3 4 5 →