Removal Rate Simulation of Dissolution-Type Electrochemical Mechanical Polishing

被引：2

作者：

Fukuda, Akira ^{[1
]}

Kodera, Akira ^{[2
]}

Toma, Yasushi ^{[2
]}

Suzuki, Tsukuru ^{[2
]}

Hiyama, Hirokuni ^{[2
]}

Doi, Toshiro ^{[1
]}

Kurokawa, Syuhei ^{[1
]}

Ohnishi, Osamu ^{[1
]}

机构：

[1] Kyushu Univ, Grad Sch, Fukuoka 8190395, Japan

[2] Ebara Corp, Kanagawa 2518502, Japan

来源：

JAPANESE JOURNAL OF APPLIED PHYSICS | 2010年 / 49卷 / 07期

关键词：

PLANARIZATION ECMP; TECHNOLOGY; ACID; PAD;

D O I：

10.1143/JJAP.49.076701

中图分类号：

O59 [应用物理学];

学科分类号：

摘要：

A new method for simulating the Cu removal rate in electrochemical mechanical polishing (ECMP) based on the dissolution-type polishing mechanism was developed. The effect of a protective layer on the Cu removal rate was considered in this method because the protective layer is a key element in the dissolution-type polishing mechanism. This method was used to simulate the removal rate in a rotary-type ECMP system. The simulations accurately provided the dependence of the Cu removal rate on the aperture ratio. Furthermore, the dependence of the Cu removal rate on the aperture ratio was described with respect to changes in the average protective layer amount with time. Regarding the dependence of the Cu removal rate on the aperture diameter, however, a discrepancy was observed between the simulation and experimental results because this method did not take into account the effect of the aperture diameter on the electrolyte-filling ratio in apertures. (C) 2010 The Japan Society of Applied Physics

引用

页码：0767011 / 0767018

页数：8

共 50 条

[31] Correction to: Electrochemical polishing versus mechanical polishing of AISI 304: surface and electrochemical study
Ahmed M. Awad Abouelata
Adel Attia
Gehan I. Youssef
Journal of Solid State Electrochemistry, 2022, 26 : 131 - 131
[32] High Removal Rate Cobalt Slurry with Glutathione on Chemical Mechanical Polishing in Alkaline Slurry
Xu, Aoxue
Feng, Daohuan
Wang, Weilei
Liu, Weili
Song, Zhitang
ECS JOURNAL OF SOLID STATE SCIENCE AND TECHNOLOGY, 2020, 9 (08)
[33] A comparative study on the roles of velocity in the material removal rate during chemical mechanical polishing
Tseng, WT
Chin, JH
Kang, LC
JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 1999, 146 (05) : 1952 - 1959
[34] Effect of process parameters on material removal rate in chemical mechanical polishing of Si(100)
Forsberg, M
MICROELECTRONIC ENGINEERING, 2005, 77 (3-4) : 319 - 326
[35] Material removal rate in chemical-mechanical polishing of wafers based on particle trajectories
苏建修
陈锡渠
杜家熙
康仁科
半导体学报, 2010, 31 (05) : 145 - 150
[36] Analysis on material removal rate in wafer chemical mechanical polishing based on trajectory of abrasives
Su, J. X.
Guo, D. M.
Kang, R. K.
Li, Q. Z.
ADVANCES IN ABRASIVE MACHINING AND SURFACING TECHNOLOGIES, PROCEEDINGS, 2006, : 335 - +
[37] Effect of cations on the improvement of material removal rate of silicon wafer in chemical mechanical polishing
Xie, Wenxiang
Zhang, Zhenyu
Chen, Xin
Yu, Shiqiang
Shi, Chunjing
Zhou, Hongxiu
Wen, Wei
COLLOIDS AND SURFACES A-PHYSICOCHEMICAL AND ENGINEERING ASPECTS, 2023, 670
[38] Material removal rate in chemical-mechanical polishing of wafers based on particle trajectories
Su Jianxiu
Chen Xiqu
Du Jiaxi
Kang Renke
JOURNAL OF SEMICONDUCTORS, 2010, 31 (05) : 0560021 - 0560026
[39] New methods to determining endpoint and real time removal rate for Chemical Mechanical Polishing
Chen, HC
Wu, JY
Lur, W
CHEMICAL MECHANICAL PLANARIZATION IN IC DEVICE MANUFACTURING III, PROCEEDINGS, 2000, 99 (37): : 555 - 564
[40] Comparative study on the roles of velocity in the material removal rate during chemical mechanical polishing
Department of Materials Science and Engineering, National Cheng-Kung University, Tainan 701, Taiwan
不详
J Electrochem Soc, 5 (1952-1959):

← 1 2 3 4 5 →