Effect of Initial Microstructure on Properties of Cryorolled Al 5052 Alloy Subjected to Different Annealing Treatment Temperatures

被引：10

作者：

Anas, N. M. ^{[1
]}

Dhindaw, B. K. ^{[2
]}

Zuhailawati, H. ^{[1
]}

Abdullah, T. K. ^{[1
]}

Anasyida, A. S. ^{[1
]}

机构：

[1] Univ Sains Malaysia, Sch Mat & Mineral Resources Engn, Struct Niche Area, Engn Campus, Nibong Tebal 14300, Pulau Pinang, Malaysia

[2] IIT Bhubaneswar, Sch Minerals Met & Mat Engn, Bhubaneswar 751007, Orissa, India

来源：

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 2018年 / 27卷 / 11期

关键词：

Al; 5052; alloy; annealing; corrosion; cryorolling; strength; MG-SI ALLOY; MECHANICAL-PROPERTIES; CORROSION BEHAVIOR; GRAIN-SIZE; ROLLING TEMPERATURE; HIGH-STRENGTH; DUCTILITY; DEFORMATION; RESISTANCE; CU;

D O I：

10.1007/s11665-018-3645-7

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Al 5052 alloy sheets were subjected to different pre-annealing temperatures (150, 200, 250, 300, and 350 degrees C) prior to cryorolling. The process resulted in Al 5052 alloys with different initial microstructures. The pre-annealed alloy sheets were compared with a cryorolled sample not subjected to pre-annealing. The thicknesses of the alloy samples after cryorolling was reduced by 30%. The pre-annealed cryorolled samples exhibited low crystallite size, and high lattice strain. Among them, the cryorolled sample pre-annealed at 300 degrees C had the lowest crystallite size, and the highest lattice strain. Changes in initial microstructure of this sample resulted in a significant improvement in its hardness (88Hv), tensile strength (333MPa), and corrosion resistance. The sample had the highest corrosion resistance among the cryorolled samples.

引用

页码：6206 / 6217

页数：12

共 50 条

[31] Effect of annealing on microstructure and mechanical properties of Al 6061 alloy processed by cryorolling
Rao, P. Nageswara
Singh, D.
Jayaganthan, R.
MATERIALS SCIENCE AND TECHNOLOGY, 2013, 29 (01) : 76 - 82
[32] The effect of annealing on the microstructure and tensile properties of a β/γ′ Ni-Al-Fe alloy
Pekarskaya, E
Botton, GA
Jones, CN
Humphreys, CJ
INTERMETALLICS, 2000, 8 (08) : 903 - 913
[33] Effect of Nonisothermal Annealing on Microstructure and Mechanical Properties of Al-Mg Alloy
Wu, Yaru
Yang, Hongfu
Lu, Shumeng
Zheng, Shanju
Yuan, Xiaohong
Peng, Yawei
Li, Mengnie
ADVANCED ENGINEERING MATERIALS, 2025, 27 (05)
[34] EFFECT OF ANNEALING TEMPERATURE ON MICROSTRUCTURE AND MECHANICAL PROPERTIES OF 5052 ALUMINUM ALLOY PIPE FITTINGS ALPINE SKIING STICKS
Ning, B. W.
Zhao, Y. P.
Luo, X. H.
Sun, L. C.
METALURGIJA, 2024, 63 (3-4): : 383 - 386
[35] Investigation of annealing treatment on the interfacial and mechanical properties of Al5052/Cu multilayered composites subjected to ARB process
Tayyebi, Moslem
Rahmatabadi, Davood
Karimi, Armin
Adhami, Maryam
Hashemi, Ramin
JOURNAL OF ALLOYS AND COMPOUNDS, 2021, 871
[36] Effect of strain rate on microstructure evolutions and mechanical properties of cryorolled Zr upon annealing
Guo, Defeng
Li, Ming
Shi, Yindong
Zhang, Zhibo
Zhang, Haitian
Liu, Xiaoman
Zhang, Xiangyi
MATERIALS LETTERS, 2012, 66 (01) : 305 - 307
[37] Effect of different annealing temperatures on microstructures and properties of Cu-Sn Alloy
Fan, Wenxin
Hui, Jun
Zai XinFeng
Gao, Weifeng
Xue, Chen
MATERIALS RESEARCH EXPRESS, 2018, 5 (10):
[38] Evolution of Microstructure and Mechanical Properties in Al 5052 Alloy During Warm Rolling
Kang, Ui Gu
Jeong, Shin Woong
Nam, Won Jong
STEEL RESEARCH INTERNATIONAL, 2010, 81 (09) : 118 - 121
[39] EFFECT OF MICROSTRUCTURE ON TENSILE PROPERTIES AT CRYOGENIC TEMPERATURES IN AL-LI ALLOY
LI, YY
YAO, DP
HU, ZQ
JIANG, XJ
CRYOGENICS, 1990, 30 : 393 - 398
[40] Microstructure and properties of the eutectic 12Si–Al alloy subjected to barothermal treatment
Dedyaeva E.V.
Nikiforov P.N.
Padalko A.G.
Talanova G.V.
Shvorneva L.I.
Russian Metallurgy (Metally), 2016, 2016 (9) : 856 - 863

← 1 2 3 4 5 →