Ball cratering test on ductile materials

被引：8
|
作者：
Camerini, Rafael Vieira [1 ,2 ,3 ]
de Souza, Rodrigo Buchfink [1 ,2 ,3 ]
de Carli, Felipe [1 ]
Pereira, Altair Soria [1 ,4 ]
Balzaretti, Naira Maria [1 ]
机构：
[1] Univ Fed Rio Grande do Sul, Inst Fis, BR-91501970 Porto Alegre, RS, Brazil
[2] Jomon Ind Artefatos Ceram Ltda, Porto Alegre, RS, Brazil
[3] Univ Fed Rio Grande do Sul, PGCIMAT, BR-91501970 Porto Alegre, RS, Brazil
[4] Univ Fed Rio Grande do Sul, Escola Engn, BR-91501970 Porto Alegre, RS, Brazil
来源：
WEAR | 2011年 / 271卷 / 5-6期
关键词：
Micro-scale abrasion; Hardness; Steel; Non-ferrous metals; Wear testing; ABRASIVE WEAR TEST; 2-BODY; STEEL;
D O I：
10.1016/j.wear.2011.03.013
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Micro-abrasive wear test, also called ball cratering test, is normally used to investigate the wear behavior of hard bulk materials or wear-resistant coatings. In this work, this test was used to investigate the wear behavior of metallic samples. The results showed that the embedment of abrasive particles and the formation of grooves in the crater's surface may induce to artificially small wear coefficient when the test is applied to ductile materials. Surface grooving was observed when the normal force applied by the sphere was higher than a critical value. This critical value depends on the hardness and mechanical strength of the material being tested. (C) 2011 Elsevier B.V. All rights reserved.
引用
收藏
页码：770 / 774
页数：5
相关论文
共 50 条
  • [31] A study on the evolution of the contact angle of small punch creep test of ductile materials
    Cacciapuoti, B.
    Sun, W.
    McCartney, D. G.
    INTERNATIONAL JOURNAL OF PRESSURE VESSELS AND PIPING, 2016, 145 : 60 - 74
  • [32] The ball on three balls test -: Strength and failure analysis of different materials
    Danzer, Robert
    Harrer, Walter
    Supancic, Peter
    Lube, Tanja
    Wang, Zhonghua
    Boerger, Andreas
    JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2007, 27 (2-3) : 1481 - 1485
  • [33] VISCOELASTIC EVALUATION OF SOFT MATERIALS AT SUBSONIC LEVEL BY BALL IMPACT TEST
    Igarashi, Katsuya
    Torii, Naoki
    Sakuma, Atsushi
    PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, 2014, VOL 14, 2015,
  • [34] Research on Tribological Features of Brake Friction Materials-Comparison of the Results Obtained with the Pin-On-Disc and Ball-Cratering Methods
    Borawski, Andrzej
    Szpica, Dariusz
    Mieczkowski, Grzegor
    MECHANIKA, 2022, 28 (04): : 317 - 322
  • [35] Study on the Influence of the Ball Material on Abrasive Particles' Dynamics in Ball-Cratering Thin Coatings Wear Tests
    Pinto, Gustavo
    Baptista, Andresa
    Silva, Francisco
    Porteiro, Jacobo
    Miguez, Jose
    Alexandre, Ricardo
    MATERIALS, 2021, 14 (03)
  • [36] The importance of material properties for cratering and penetration in geologic materials
    Curran, DR
    SHOCK COMPRESSION OF CONDENSED MATTER - 1997, 1998, 429 : 945 - 948
  • [37] Application of response surface methodology in ball-cratering abrasive wear testing
    Osuch-Slomka, Edyta
    Ruta, Ryszard
    Slomka, Zbigniew
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART J-JOURNAL OF ENGINEERING TRIBOLOGY, 2015, 229 (11) : 1379 - 1392
  • [38] Ductile or Partial Ductile Mode Machining of Brittle Materials
    Z.W. Zhong
    The International Journal of Advanced Manufacturing Technology, 2003, 21 : 579 - 585
  • [39] Ductile or partial ductile mode machining of brittle materials
    Zhong, ZW
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2003, 21 (08): : 579 - 585
  • [40] OBLIQUE IMPACT OF A HARD BALL AGAINST DUCTILE, SEMI-INFINITE TARGET MATERIALS - EXPERIMENT AND ANALYSIS.
    Sundararajan, G.
    Shewmon, P.G.
    International Journal of Impact Engineering, 1987, 6 (01) : 3 - 22
12345