Influence of Iron Carbide on Mechanical Properties in High Silicon-added Medium-carbon Martensitic Steels

被引:1
|
作者
Teramoto, Shinya [1 ,2 ]
Imura, Masahito [3 ]
Masuda, Yuki [4 ]
Ishida, Toshinori [5 ]
Ohnuma, Masato [6 ]
Neishi, Yutaka [1 ]
Suzuki, Takahisa [7 ]
机构
[1] Nippon Steel Corp Ltd, Muroran R&D Lab, Tokyo, Japan
[2] Hokkaido Univ, Grad Sch Engn, Sapporo, Hokkaido, Japan
[3] DMG Mori BUG Corp, Sapporo, Hokkaido, Japan
[4] Cent Japan Railway Co, Nagoya, Aichi, Japan
[5] JFE Steel Corp, Tokyo, Japan
[6] Hokkaido Univ, Fac Engn, Sapporo, Hokkaido, Japan
[7] Nippon Steel Corp Ltd, Yawata R&D Lab, Tokyo, Japan
来源
TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN | 2020年 / 106卷 / 03期
关键词
medium carbon steel; tempered martensite; carbide; yield strength; microscopy; small-angle scattering; X-ray diffractometry; CHI-CARBIDE; PRECIPITATION; DIFFRACTION;
D O I
10.2355/tetsutohagane.TETSU-2019-085
中图分类号
TF [冶金工业];
学科分类号
0806 ;
摘要
Using a medium-carbon steel containing 2 mass% Si, we investigated the effect of its tempered martensite microstructure on its mechanical properties. We found that the tensile strength of tempered martensite continuously decreases with increasing tempering temperature and that its yield strength markedly decreases in a tempering temperature range of 673 K to 723 K. To investigate the correlation with the microstructure, we examined the effect of tempering temperature on the microstructure by SEM and TEM and identified Fe carbide phases by TEM nanobeam diffraction pattern analysis and X-ray diffractometry. In the tempering temperature range where the yield strength significantly decreases, the morphology of the epsilon carbide precipitated in martensite blocks changed from platelike to granular and the chi carbide was precipitated in a small amount in the samples tempered at 723 K. SAXS quantitative evaluation of the epsilon carbide revealed that the decrease in the size and volume fraction of the epsilon carbide with the increase in the tempering temperature was far greater than with the samples tempered at 673 K and below. The sharp decrease in the yield strength was suggested to be correlated with the increase in the mobility of dislocations with the decrease in the precipitate volume fraction resulting from the dissolution of epsilon carbide in the transformation process of the Fe carbides.
引用
收藏
页码:165 / 173
页数:9
相关论文
共 50 条
  • [41] Precipitation Hardening and Mechanical Properties in Cu Added Martensitic Ultra-high Strength Steels
    Nagataki, Yasunobu
    Sato, Kaoru
    Hosoya, Yoshihiro
    TETSU TO HAGANE-JOURNAL OF THE IRON AND STEEL INSTITUTE OF JAPAN, 2008, 94 (11): : 553 - 561
  • [42] Characteristics of carbide-free medium-carbon bainitic steels in high-stress abrasive wear conditions
    Haiko, Oskari
    Kaikkonen, Pentti
    Somani, Mahesh
    Valtonen, Kati
    Komi, Jukka
    WEAR, 2020, 456
  • [43] Influence carbon and/or iron carbide on the structure and properties of dual-phase steels
    El-Sesy, IA
    El-Baradie, ZM
    MATERIALS LETTERS, 2002, 57 (03) : 580 - 585
  • [44] INFLUENCE OF IMPURITIES AND GASES ON THE QUALITY OF MEDIUM-CARBON STRUCTURAL-STEELS
    FEDOROVA, IP
    KOVAL, VK
    TARASOVA, VA
    LISNYAK, AG
    RUSSIAN METALLURGY, 1988, (03): : 100 - 102
  • [45] Microstructure development and mechanical properties of medium carbon carbide-free bainite steels
    Soliman, Mohamed
    Palkowski, Heinz
    11TH INTERNATIONAL CONFERENCE ON TECHNOLOGY OF PLASTICITY, ICTP 2014, 2014, 81 : 1306 - 1311
  • [46] Effect of Tempering Temperature on the Structure and Mechanical Properties of Medium-Carbon Steel with Elevated Silicon Content
    Borisov, S. I.
    Borisova, Yu. I.
    Tkachev, E. S.
    Knyazyuk, T. V.
    Gaidar, S. M.
    Kaibyshev, R. O.
    METAL SCIENCE AND HEAT TREATMENT, 2024, 66 (1-2) : 17 - 24
  • [47] Modeling Thermal Welding Cycles of Medium-Carbon High-Strength Steels for Predicting the Mechanical Properties of Real Welded Joints
    A. A. Pavlov
    V. L. Evtukhov
    P. S. Yakovleva
    V. V. Semenov
    G. N. Eremin
    Metallurgist, 2024, 67 : 1516 - 1522
  • [48] Microstructural Characteristics and Mechanical Properties of Low-Alloy, Medium-Carbon Steels After Multiple Tempering
    Erfan Abbasi
    Quanshun Luo
    Dave Owens
    ActaMetallurgicaSinica(EnglishLetters), 2019, 32 (01) : 74 - 88
  • [49] Modeling Thermal Welding Cycles of Medium-Carbon High-Strength Steels for Predicting the Mechanical Properties of Real Welded Joints
    Pavlov, A. A.
    Evtukhov, V. L.
    Yakovleva, P. S.
    Semenov, V. V.
    Eremin, G. N.
    METALLURGIST, 2024, 67 (9-10) : 1516 - 1522
  • [50] Microstructural Characteristics and Mechanical Properties of Low-Alloy, Medium-Carbon Steels After Multiple Tempering
    Erfan Abbasi
    Quanshun Luo
    Dave Owens
    Acta Metallurgica Sinica (English Letters), 2019, 32 : 74 - 88