Machining of insulating materials by EDM with micro-pin electrode

被引：0

作者：

Tani, Takayuki ^{[1
]}

Mohri, Naotake

Gotoh, Hiromitsu ^{[1
]}

Haruo, Sai

Okada, Masaaki

机构：

[1] Tsukuba Univ Technol, Dept Ind Informat, Tsukuba, Ibaraki 3058520, Japan

来源：

PROCEEDINGS OF THE 15TH INTERNATIONAL SYMPOSIUM ON ELECTROMACHINING | 2007年

关键词：

electrical discharge machining; micromachining; scanning EDM; insulating ceramics;

D O I：

暂无

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

This study describes a new method for micro-pin electrode formation and its application to micro machining of insulating ceramics. The rotating electrode is moved through the inside of the working plate with scanning EDM, then it changes into a micro-pin with a very small diameter. Two electrically isolated plates were set in position, and movement of the electrode is controlled to maintain a centered position by measuring current to the isolated plates. Machined diameter closely corresponded to the desired diameter. A micro hole of 30 mu m diameter was drilled into insulating Si3N4 ceramics using a formed micro-pin electrode.

引用

页码：257 / 261

页数：5

共 50 条

[21] Probability of precision micro-machining of insulating Si3N4 ceramics by EDM
Muttamara, A
Fukuzawa, Y
Mohri, N
Tani, T
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2003, 140 : 243 - 247
[22] Experimental Investigation of Forced Convection on Square Micro-Pin Fins
Niranjan, Ramendra Singh
Singh, Onkar
Ramkumar, J.
ADVANCES IN FLUID AND THERMAL ENGINEERING, 2019, : 117 - 126
[23] Reliability Study of Micro-Pin Fin Array for On-Chip Cooling
Woodrum, David C.
Sarvey, Thomas
Bakir, Muhannad S.
Sitaraman, Suresh K.
2015 IEEE 65TH ELECTRONIC COMPONENTS AND TECHNOLOGY CONFERENCE (ECTC), 2015, : 2283 - 2287
[24] FLOW MORPHOLOGIES AND BUBBLE DYNAMICS IN MICROCHANNELS WITH ENTRENCHED MICRO-PIN FINS
Krishnamurthy, Santosh
Peles, Yoav
PROCEEDINGS OF THE 9TH BIENNIAL CONFERENCE ON ENGINEERING SYSTEMS DESIGN AND ANALYSIS - 2008, VOL 4, 2009, : 295 - 302
[25] Investigations on reduction of tool electrode wear in micro-EDM using novel electrode materials
Uhlmann, Eckart
Roehner, Markus
CIRP JOURNAL OF MANUFACTURING SCIENCE AND TECHNOLOGY, 2008, 1 (02) : 92 - 96
[26] Fabrication of Flexible Base Micro-pin Array and Wall Attachment Application
Park, Jong Wuk
INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2020, 21 (05) : 787 - 795
[27] Fabrication of Flexible Base Micro-pin Array and Wall Attachment Application
Jong Wuk Park
International Journal of Precision Engineering and Manufacturing, 2020, 21 : 787 - 795
[28] Micro-spherical probes machining by EDM
Sheu, DY
JOURNAL OF MICROMECHANICS AND MICROENGINEERING, 2005, 15 (01) : 185 - 189
[29] Influence of ECM pulse conditions on WC alloy micro-pin fabrication
Natsu, W.
Kurahata, D.
PROCEEDINGS OF THE SEVENTEENTH CIRP CONFERENCE ON ELECTRO PHYSICAL AND CHEMICAL MACHINING (ISEM), 2013, 6 : 401 - 406
[30] Effects of Electrode and Workpiece Materials on the Sustainability of Micro-EDM Drilling Process
Gianluca D’Urso
Claudio Giardini
Chiara Ravasio
International Journal of Precision Engineering and Manufacturing, 2018, 19 : 1727 - 1734

← 1 2 3 4 5 →