Machining of insulating materials by EDM with micro-pin electrode

被引：0
|
作者：
Tani, Takayuki [1 ]
Mohri, Naotake
Gotoh, Hiromitsu [1 ]
Haruo, Sai
Okada, Masaaki
机构：
[1] Tsukuba Univ Technol, Dept Ind Informat, Tsukuba, Ibaraki 3058520, Japan
来源：
PROCEEDINGS OF THE 15TH INTERNATIONAL SYMPOSIUM ON ELECTROMACHINING | 2007年
关键词：
electrical discharge machining; micromachining; scanning EDM; insulating ceramics;
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
This study describes a new method for micro-pin electrode formation and its application to micro machining of insulating ceramics. The rotating electrode is moved through the inside of the working plate with scanning EDM, then it changes into a micro-pin with a very small diameter. Two electrically isolated plates were set in position, and movement of the electrode is controlled to maintain a centered position by measuring current to the isolated plates. Machined diameter closely corresponded to the desired diameter. A micro hole of 30 mu m diameter was drilled into insulating Si3N4 ceramics using a formed micro-pin electrode.
引用
收藏
页码：257 / 261
页数：5
相关论文
共 50 条
  • [1] Micro-pin electrodes formation by micro-scanning EDM process
    Mohri, Naotake
    Tani, Takayuki
    CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2006, 55 (01) : 175 - 178
  • [2] Concept development for fabricating threaded micro-pin using wire-EDM
    Tapas Debnath
    Promod Kumar Patowari
    Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2019, 41
  • [3] Concept development for fabricating threaded micro-pin using wire-EDM
    Debnath, Tapas
    Patowari, Promod Kumar
    JOURNAL OF THE BRAZILIAN SOCIETY OF MECHANICAL SCIENCES AND ENGINEERING, 2019, 41 (10)
  • [4] Electrochemical machining of tungsten carbide alloy micro-pin with NaNO3 solution
    Naoki Shibuya
    Yukihiro Ito
    Wataru Natsu
    International Journal of Precision Engineering and Manufacturing, 2012, 13 : 2075 - 2078
  • [5] Electrochemical machining of tungsten carbide alloy micro-pin with NaNO3 solution
    Shibuya, Naoki
    Ito, Yukihiro
    Natsu, Wataru
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2012, 13 (11) : 2075 - 2078
  • [6] Experimental research on machining performance of electrode materials in dry EDM
    Li, Liqing
    Wang, Zhenlong
    Guo, Yongfeng
    Bai, Jicheng
    ADVANCES IN MATERIALS MANUFACTURING SCIENCE AND TECHNOLOGY II, 2006, 532-533 : 173 - +
  • [7] New Researches for Fabrication of Micro-pin in Micro-ECM
    Wang, Minghuan
    Wang, Tao
    Peng, Wei
    ULTRA-PRECISION MACHINING TECHNOLOGIES, 2012, 497 : 205 - 209
  • [8] Machining of PCD by micro EDM
    Sheu, Dong-Yea
    INDUSTRIAL DIAMOND REVIEW, 2006, (04): : 29 - 31
  • [9] The Machining Characteristics of Insulating AlN Ceramics by EDM
    Kensei, Kaneko
    Ken, Yamashita
    Yasushi, Fukuzawa
    EMERGING TECHNOLOGY IN PRECISION ENGINEERING XIV, 2012, 523-524 : 328 - +
  • [10] Experimental investigation on simultaneous machining of EDM and ECM with different electrode materials
    Meng, Jianbing
    Guan, Qingyi
    Wang, Shuaike
    Dong, Xiaojuan
    Li, Li
    Yu, Haoyang
    Zhao, Guoyong
    Zhao, Yugang
    SURFACE TOPOGRAPHY-METROLOGY AND PROPERTIES, 2022, 10 (04):
12345