The effect of tuber pre-heating temperature and storage time on the mechanical properties of potatoes

被引:25
|
作者
Laza, M
Scanlon, MG [1 ]
Mazza, G
机构
[1] Univ Manitoba, Dept Food Sci, Winnipeg, MB R3T 2N2, Canada
[2] Pacific Agrifood Res Ctr, Food Res Program, Summerland, BC V0H 1Z0, Canada
基金
加拿大自然科学与工程研究理事会;
关键词
potato; potato storage; turgor pressure; pre-heating; slicing;
D O I
10.1016/S0963-9969(01)00086-2
中图分类号
TS2 [食品工业];
学科分类号
0832 ;
摘要
Changes in mechanical properties of potatoes are known to affect the quality of the products processed from the tubers. This study set out to ascertain the extent to which the changes in mechanical properties were attributable to turgor changes in the course of a storage season versus physiological changes that are expected to occur due to tissue ageing. Specimens taken from two potato cultivars (Russet Burbank and Shepody) of two different solids contents were subjected to small strain oscillatory shear tests and wedge-penetration fracture tests. Prior to mechanical testing, specimens prepared from control (8 degreesC) and pre-heated (33, 47 or 60 degreesC) potato tubers were osmotically adjusted in a mannitol solution of 3, 5 or 7%. The tests were repeated every month from November to June. Turgor pressure and specific gravity were also measured during storage: turgor pressure slightly decreased, while specific gravity increased slightly throughout the storage period. Control and pre-heating temperatures of 33 and 47 degreesC had little or no influence on shear modulus or fracture toughness; at a given mannitol concentration, pre-heating at 60 degreesC caused both parameters to decrease. As mannitol concentration increased, the mechanical properties investigated decreased for the control, as well as for 33 and 47 degreesC pre-heating treatments. Mannitol concentration had no effect on shear modulus and toughness for tubers that had been pre-heated at 60 degreesC. Storage time had only a slight effect on the parameters of interest. Solids content and cultivar had no significant effect on either shear modulus or fracture toughness. To conclude, mechanical properties of tubers did change in storage, but the changes were much less pronounced than the changes caused by adjustment of turgor pressure. Thus, cell moisture content and its effect on turgor pressure affects tissue mechanical properties more dramatically than changes associated with ageing. (C) 2001 Elsevier Science Ltd. All rights reserved.
引用
收藏
页码:659 / 667
页数:9
相关论文
共 50 条
  • [41] Effect of Baking Furnace fire pre-heating configuration on environment characteristics
    Miotto, P
    Kato, C
    Silva, MA
    Figueiredo, F
    Piffer, V
    LIGHT METALS 2005, 2005, : 689 - 692
  • [42] Effect of pre-heating methods and devices on the mechanical properties, post-gel shrinkage, and shrinkage stress of bulk-fill materials
    Hordones Ribeiro, Maria Tereza
    de Braganca, Gabriel Felipe
    Sales Oliveira, Lais Rani
    Lourenco Braga, Stella Sueli
    Quirino de Oliveira, Helena Leticia
    Price, Richard Bengt
    Soares, Carlos Jose
    JOURNAL OF THE MECHANICAL BEHAVIOR OF BIOMEDICAL MATERIALS, 2023, 138
  • [43] Influence of pre-heating and ceramic thickness on physical properties of luting agents
    Lima, Michele O.
    Catelan, Anderson
    Marchi, Giselle M.
    Lima, Debora A. N. L.
    Martins, Luis R. M.
    Aguiar, Flavio H. B.
    JOURNAL OF APPLIED BIOMATERIALS & FUNCTIONAL MATERIALS, 2018, 16 (04): : 252 - 259
  • [44] Effect of pre-heating temperature on the characteristics of sol-gel derived lead zirconate titanate films
    Thoumtom, Sarawut
    Rujijanagul, Gobwute
    Tontrakoon, Jerapong
    Tunkasiri, Tawee
    SURFACE REVIEW AND LETTERS, 2008, 15 (1-2) : 65 - 70
  • [45] Effect of Pre-heating on AC Breakdown Strength of Oil Barrier Tube
    Reddy, G. Nithin
    Reddy, C. C.
    PROCEEDINGS OF 2020 INTERNATIONAL SYMPOSIUM ON ELECTRICAL INSULATING MATERIALS (ISEIM 2020), 2020, : 549 - 551
  • [46] Effect of moisture content, heating time and temperature on the bending mechanical properties of Phyllostachys iridescens
    Wang, Xuehua
    Zhu, Junjie
    Zhong, Yong
    Sun, Fengbo
    Fei, Benhua
    EUROPEAN JOURNAL OF WOOD AND WOOD PRODUCTS, 2024, 82 (03) : 657 - 668
  • [47] The effect of resin composite pre-heating on monomer conversion and polymerization shrinkage
    Lohbauer, Ulrich
    Zinelis, Spiros
    Rahiotis, Christos
    Petschelt, Anselm
    Eliades, George
    DENTAL MATERIALS, 2009, 25 (04) : 514 - 519
  • [48] Heat storage device for pre-heating internal combustion engines at start-up
    Vasiliev, LL
    Burak, VS
    Kulakov, AG
    Mishkinis, DA
    Bohan, PV
    INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 1999, 38 (01) : 98 - 104
  • [49] Improved cure optimization in pultrusion with pre-heating and die-cooler temperature
    Joshi, SC
    Lam, YC
    Tun, UW
    COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2003, 34 (11) : 1151 - 1159
  • [50] Experimental Study on the Effects of Pre-Heating a Battery in a Low-Temperature Environment
    Song, Hyun-Sik
    Jeong, Jin-Beom
    Lee, Baek-Haeng
    Shin, Dong Hyun
    Kim, Byoung-Hoon
    Kim, Tae-Hoon
    Heo, Hoon
    2012 IEEE VEHICLE POWER AND PROPULSION CONFERENCE (VPPC), 2012, : 1198 - 1201