Effect of nitrogen content on physical properties of glass fiber reinforced polyamide 6 prepared by microcellular injection molding

被引：8

作者：

Sykutera, Dariusz ^{[1
]}

Szewczykowski, Piotr ^{[1
]}

Roch, Mateusz ^{[1
]}

Wajer, Lukasz ^{[1
]}

Grabowski, Marek ^{[2
]}

Bielinski, Marek ^{[1
]}

机构：

[1] UTP Univ Sci & Technol, Inst Mfg Technol, Dept Mat Engn & Polymer Proc, Al Prof S Kaliskiego 7, PL-85796 Bydgoszcz, Poland

[2] GRAFORM Co, Wroblowa 7, PL-85437 Bydgoszcz, Poland

来源：

POLIMERY | 2018年 / 63卷 / 11-12期

关键词：

microcellular injection molding; MuCell (R) technology; polyamide PA6 GF30; porous materials; mechanical properties; MOLDED PARTS; BLOWING AGENTS; POLYPROPYLENE; TECHNOLOGY; MUCELL(R); FOAMS;

D O I：

10.14314/polimery.2018.11.1

中图分类号：

O63 [高分子化学（高聚物）];

学科分类号：

070305 ; 080501 ; 081704 ;

摘要：

The aim of the study was to determine the effect of the amount of nitrogen dosed in supercritical state to polymer melt on structure and physical properties of large-scale molded pieces from polyamide PA6 GF30, obtained in the process of microcellular injection molding with gas dosage using MuCell (R) method. Apart from the reduction of the density at a level of about 15 % for samples with the highest nitrogen content, the increase of the impact resistance of samples PA6 GF30 was observed. The other investigated mechanical properties were maintained at a good level.

引用

页码：743 / 749

页数：7

共 50 条

[41] Effect of Glass Fiber Content on Microstructure and Mechanical Properties of Glass Fiber Reinforced Polycarbonate
Li Y.
Xin Y.
Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering, 2019, 35 (05): : 27 - 31
[42] Impact properties of injection molded glass fiber/polyamide-6 composites: effect of testing parameters
Hassan, Aziz
Hassan, Asfarina A.
Rafiq, M. I. Mohd
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2011, 30 (10) : 889 - 898
[43] GLASS FIBER REINFORCED THERMOPLASTIC COMPOSITES Effect of Polyamide Blend on Fiber/Matrix Interfacial Properties of Glass Fiber Reinforced Thermoplastic Composites
Aratani, Yusuke
Kenjo, Yuta
Tanaka, Kazuto
SAMPE JOURNAL, 2022, 58 (03) : 62 - 69
[44] Impact and Tensile Properties of Injection-Molded Glass Fiber Reinforced Polyamide 6 -Processing Temperature and Pressure Optimization
Budiyantoro, Cahyo
Rochardjo, Heru S. B.
Wicaksono, Satrio E.
Ad, Muhammad Alek
Saputra, I. Nyoman
Alif, Rahman
INTERNATIONAL JOURNAL OF TECHNOLOGY, 2024, 15 (03) : 597 - 607
[45] Mechanical, thermal and morphological properties of glass fiber and carbon fiber reinforced polyamide-6 and polyamide-6/clay nanocomposites
Wu, SH
Wang, FY
Ma, CCM
Chang, WC
Kuo, CT
Kuan, HC
Chen, WJ
MATERIALS LETTERS, 2001, 49 (06) : 327 - 333
[46] Tensile, impact and fiber length properties of injection-molded short and long glass fiber-reinforced polyamide 6,6 composites
Hassan, A
Yahya, R
Yahaya, AH
Tahir, ARM
Hornsby, PR
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2004, 23 (09) : 969 - 986
[47] Improvement of mechanical properties of long jute fiber reinforced polylactide prepared by injection molding process
Fujiura, T.
Okamoto, T.
Tanaka, T.
Imaida, Y.
DESIGN AND NATURE V: COMPARING DESIGN IN NATURE WITH SCIENCE AND ENGINEERING, 2010, 138 : 181 - +
[48] Influence of fiber length and compatibilizer on mechanical properties of long glass fiber reinforced polyamide 6,6
Yang, Bin
Leng, Jinhua
He, Bobing
Liu, Heng
Zhang, Yu
Duan, Zhaohua
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2012, 31 (16) : 1103 - 1112
[49] Influence of fiber length and compatibilizer on mechanical properties of long glass fiber reinforced polyamide 6,6
College of Chemistry, Sichuan University, Chengdu 610064, China
不详
J Reinf Plast Compos, 16 (1103-1112):
[50] Injection molding of glass fiber reinforced phenolic composites. 2: Study of the injection molding process
Singh, R
Chen, F
Jones, FR
POLYMER COMPOSITES, 1998, 19 (01) : 37 - 47

← 1 2 3 4 5 →