Investigation of the tribological properties of Ti-TiN-(Ti,Al,Nb,Zr)N composite coating and its efficiency in increasing wear resistance of metal cutting tools

被引:29
|
作者
Grigoriev, Sergey [1 ]
Vereschaka, Alexey [2 ]
Milovich, Filipp [3 ]
Migranov, Mars [1 ]
Andreev, Nikolay [3 ]
Bublikov, Jury [2 ]
Sitnikov, Nikolay [4 ]
Oganyan, Gaik [1 ]
机构
[1] Moscow State Technol Univ STANKIN, Vadkovsky Per 1, Moscow 127994, Russia
[2] IDTI RAS, Vadkovsky Per 18-1a, Moscow 127994, Russia
[3] Natl Univ Sci & Technol MISiS, Leninsky Prospect 4, Moscow 119049, Russia
[4] Keldysh Res Ctr, State Sci Ctr, Onezhskaya St 8, Moscow 125438, Russia
基金
俄罗斯科学基金会;
关键词
Multilayer composite multicomponent coating; Diffusion; Wear; Metal-cutting tool; Plastic deformation; TI-ZR-N; MECHANICAL-PROPERTIES; HARD COATINGS; THIN-FILMS; THERMAL-STABILITY; COATED TOOLS; VACUUM-ARC; AL; PERFORMANCE; TEMPERATURE;
D O I
10.1016/j.triboint.2021.107236
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
The paper offers the findings of the investigation focused on the tribological properties of a sample with the Ti-TiN-(Ti,Al,Nb,Zr)N coating depending on temperature, which varied in the range of 500-1000 degrees C. It is found that as the temperature rises to 700 degrees C and higher, the adhesion component f(adh) of the coefficient of friction (COF) measured for a coated sample becomes significantly lower (by about 20%) as compared to the value of f(adh) for an uncoated sample. The paper also describes the results of the studies of the wear pattern on a metal-cutting tool depending on the cutting speed (v(c) = 300 and 400 m/min). With an increase in the cutting speed from 300 to 400 m/min, the depth of diffusion of iron (Fe) into the coating increases by 56%, while the depth of diffusion of titanium (Ti) and other coating elements into the material being machined increases by 35%. With an increase in the cutting speed, the value of the adhesion component f(adh) of the COF slightly decreases and, accordingly, the value of the adhesion component of the tool wear mechanism declines. At the same time, the diffusion mechanisms become more active, and the direct temperature effect on the coating increases, which provokes the formation of internal transverse cracks and delaminations.
引用
收藏
页数:15
相关论文
共 50 条
  • [41] Structure and properties of the cutting tools made from cemented carbides and cermets with the TiN plus mono-, gradient- or multi (Ti,Al,Si)N+TiN nanocrystalline coatings
    Dobrzanski, LA
    Golombek, K
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2005, 164 : 805 - 815
  • [42] Influence of N2 Flow Rate on the Microstructure, Mechanical, and Tribological Properties of Ti-Al-Cr-N Coating: Dry Milling Investigation on 6061 Aluminum Alloy
    Chen, Qiang
    Su, Mingxu
    Liang, Dandan
    Zhang, Yefei
    Zhou, Qiong
    Zhang, Ergeng
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2025, 34 (05) : 4303 - 4314
  • [43] Effects of Thermo-physical properties of Ti0.41Al0.59N coating on transient and steady cutting temperature distributions in coated cemented carbide tools
    Zhao, Jinfu
    Liu, Zhanqiang
    INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER, 2018, 96 : 80 - 89
  • [44] Investigation of wear mechanisms for the rake face of a cutting tool with a multilayer composite nanostructured Cr-CrN-(Ti,Cr,Al,SON coating in high-speed steel turning
    Vereschaka, Alexey
    Tabakov, Vladimir
    Grigoriev, Sergey
    Sitnikov, Nikolay
    Milovich, Filipp
    Andreev, Nikolay
    Bublikov, Jury
    WEAR, 2019, 438
  • [45] Properties of TiN-Al2O3-TiCN-TiN, TiAlN, and DLC-coated Ti(C,N)-based cermets and their wear behaviors during dry cutting of 7075 aluminum alloys
    Liu, Junbo
    Xiong, Ji
    Zhou, Li
    Guo, Zhixing
    Wen, Huiting
    You, Qianbing
    Li, Xiangrong
    Liu, Jian
    Zhao, Wu
    INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, 2021, 18 (03) : 792 - 802
  • [46] The Microstructural Properties and Tribological Performance of Al2O3 and TiN Nanoparticles Reinforced Ti-6Al-4V Composite Coating Deposited on AISI304 Steel by TIG Cladding
    Kumar, Joijode Kiran
    Rao, Thella Babu
    Krishna, Konjeti Rama
    JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME, 2023, 145 (01):
  • [47] Laser Cladding of Zr52.5Cu17.9Ni14.6Al10Ti5/TiC Composite Coating On AZ91D Magnesium Alloy for Improvement of Wear Resistance
    Huang, Kaijin
    Wang, Cunshan
    Xie, Changsheng
    ADVANCED SYNTHESIS AND PROCESSING TECHNOLOGY FOR MATERIALS, 2009, 66 : 206 - +
  • [48] High-temperature oxidation resistance, mechanical and wear resistance properties of Ti(C,N)-based cermets with Al0.3CoCrFeNi high-entropy alloy as a metal binder
    Fang, Yihang
    Chen, Nan
    Du, Guoping
    Zhang, Mengxian
    Zhao, Xianrui
    Cheng, Hu
    Wu, Jianbo
    JOURNAL OF ALLOYS AND COMPOUNDS, 2020, 815 (815)
  • [49] One-step preparation of TiO2/MoS2 composite coating on Ti6Al4V alloy by plasma electrolytic oxidation and its tribological properties
    Mu, Ming
    Liang, Jun
    Zhou, Xinjian
    Xiao, Qian
    SURFACE & COATINGS TECHNOLOGY, 2013, 214 : 124 - 130
  • [50] Effect of normal load on tribological properties of Ni60/h-BN self-lubricating anti-wear composite coating on Ti6Al4V alloy by laser cladding
    School of Mechanical and Electric Engineering, Suzhou University, Suzhou
    Jiangsu
    215006, China
    不详
    Gansu
    730000, China
    不详
    Jiangsu
    215104, China
    不详
    Jiangsu
    212013, China
    Mocaxue Xuebao, 4 (407-414):