Effect of additional current on cutting mechanism of free machining steels in turning

被引：0

作者：

Tanaka, R ^{[1
]}

Hosokawa, A ^{[1
]}

Yamada, K ^{[1
]}

Ueda, T ^{[1
]}

机构：

[1] Kanazawa Univ, Grad Sch Nat Sci & Technol, Div Mech Sci & Engn, Kanazawa, Ishikawa 9208667, Japan

来源：

PROGRESS OF MACHINING TECHNOLOGY | 2004年

关键词：

turning; carbide tool; tool wear; free machining steel; belag; AlN; electrical current;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

It is well known that the electro motive force generated at an interface between tool and workplece in cutting influences on the shape of built-up edge and the tool life. There is, however, few reports about the current flow in the closed circuit of tool-workpiece-machine on the behavior of deposited layer called "belag" observed in machining workmaterials such as calcium deoxidized steel and BN added steel and so on. This paper deals with the machinability of steels in turning with additional current. Tested workmaterials were plane carbon steel JIS S45C and BN added steel which has good machinability at high cutting speed. Turning tests were performed by carbide tool P30 in order to investigate the influence of electrical conditions of closed circuit system on the cutting mechanism of BN added steel. The tool life, cutting force, chip geometries and others were investigated practically and these results were discussed.

引用

页码：786 / 791

页数：6

共 50 条

[41] EMPIRICAL MODELING OF DIRECT ELECTRIC CURRENT EFFECT ON MACHINING CUTTING FORCE
Jones, Elizabeth
Jones, Joshua J.
Mears, Laine
PROCEEDINGS OF THE ASME 8TH INTERNATIONAL MANUFACTURING SCIENCE AND ENGINEERING CONFERENCE - 2013, VOL 1, 2013,
[42] FREE MACHINING STEELS FOR CLOCK PARTS
BUGROVA, NI
METAL SCIENCE AND HEAT TREATMENT, 1979, 21 (5-6) : 473 - 475
[43] Optimization of cutting tool geometry and machining parameters in turning process
Saravanamurugan, S.
Sundar, B. Shyam
Pranav, R. Sibi
Shanmugasundaram, A.
MATERIALS TODAY-PROCEEDINGS, 2021, 38 : 3351 - 3357
[44] Turning of BN free-machining steel
Tanaka, Ryutaro
Yamane, Yasuo
Sekiya, Katsuhiko
Narutaki, Norihiko
Shiraga, Tetsuo
Progress of Machining Technology, Proceedings, 2006, : 477 - 483
[45] Effect of secondary hardening on cutting forces, cutting temperature, and tool wear in hard turning of high alloy tool steels
El Hakim, M. A.
Shalaby, M. A.
Veldhuis, S. C.
Dosbaeva, G. K.
MEASUREMENT, 2015, 65 : 233 - 238
[46] Low Environmental Impact Machining Processes of Free Cutting Austenitic Stainless Steels without Lead Addition
Li, Zhuang
Wu, Di
Lv, Wei
RENEWABLE AND SUSTAINABLE ENERGY II, PTS 1-4, 2012, 512-515 : 1923 - +
[47] EFFECT OF TYPE OF SULFIDE FORMATION ON MACHINABILITY OF FREE-CUTTING STEELS
RADTKE, D
SCHREIBE.D
STAHL UND EISEN, 1966, 86 (02): : 89 - &
[48] TELLURIDES IN FREE-CUTTING STEELS
SALTER, WJM
PICKERIN.FB
JOURNAL OF THE IRON AND STEEL INSTITUTE, 1967, 205 : 973 - &
[49] An investigation of the cutting process for chip breaking monitoring in turning of steels
Grzesik, W
Bernat, P
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 1998, 120 (03): : 555 - 562
[50] Investigating Flank Wear and Cutting Force on Hard Steels by CBN Cutting Tool by Turning
Thamizhmanii, S.
Hasan, S.
WORLD CONGRESS ON ENGINEERING 2008, VOL III, 2008, : 1819 - 1823

← 1 2 3 4 5 →