Mechanical properties of P/M 316L stainless steel materials

被引：87

作者：

Kurgan, N. ^{[1
]}

Varol, R. ^{[2
]}

机构：

[1] Karabuk Univ, Fac Engn, Karabuk, Turkey

[2] Bartin Univ, Fac Engn, Bartin, Turkey

来源：

POWDER TECHNOLOGY | 2010年 / 201卷 / 03期

关键词：

Powder metallurgy; 316L Stainless steel; Sintering; Mechanical property;

D O I：

10.1016/j.powtec.2010.03.041

中图分类号：

TQ [化学工业];

学科分类号：

0817 ;

摘要：

In this work, 316L stainless steel (SS) powder was used. The composition of the powder is as follows: 0.015% C, 1.75% Mn, 0.45% Si, 17.24% Cr, 2.79% Mo, 14.65% Ni, and balance iron. Mixed powder was compressed cold using single action press under 800 MPa pressure. Compressed samples were sintered at 1200 degrees C, 1250 degrees C, and 1300 degrees C into the nitrogen gas atmosphere. In order to determine the mechanical properties of the produced specimens, the fatigue tests, tensile test, three-point bending test, impact test and hardness tests were applied to the specimens. Determined mechanical properties in the result of this work were compared to the properties as stated in ASTM F138-G2. Besides that to define the microstructures of the produced specimens in detail, metallographic studies were performed. (C) 2010 Elsevier B.V. All rights reserved.

引用

页码：242 / 247

页数：6

共 50 条

[41] Microstructural evolution and mechanical properties of 316L stainless steel using multiaxial forging
Rajput, S. K.
Kumar, Jitendra
Mehta, Yashwant
Soota, Tarun
Saxena, K. K.
ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES, 2020, 6 (03) : 509 - 518
[42] Cryogenic mechanical properties of 316L stainless steel fabricated by selective laser melting
Wang, Chao
Lin, Xin
Wang, Lilin
Zhang, Shuya
Huang, Weidong
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 815
[43] Microstructure and mechanical properties of friction stir processed AISI 316L stainless steel
Hajian, M.
Abdollah-zadeh, A.
Rezaei-Nejad, S. S.
Assadi, H.
Hadavi, S. M. M.
Chung, K.
Shokouhimehr, M.
MATERIALS & DESIGN, 2015, 67 : 82 - 94
[44] INFLUENCE OF SUBSTRATE MECHANICAL PROPERTIES ON DEPOSITION BEHAVIOUR OF 316L STAINLESS STEEL POWDER
Ma Guanglu
Cui Xinyu
Shen Yanfang
Cinca, Nuria
Guilemany, Josep M.
Xiong Tianying
ACTA METALLURGICA SINICA, 2016, 52 (12) : 1610 - 1618
[45] Effect of electropulsing and annealing treatment on microstructure and mechanical properties of 316L stainless steel
Ma, Yunrui
Dong, Manling
Geng, Jinfeng
Xin, Weifeng
Meng, Lingxiao
Yang, Huajie
Zhang, Zhefeng
AIP ADVANCES, 2022, 12 (10)
[46] Effect of Temperature on Microstructure and Mechanical Properties of 316L Stainless Steel Brazed Joints
Gu, Xiaolong
Yang, Changjin
Chen, Zhuojun
Wu, Chengdong
Feng, Longlong
MATERIALS PROCESSING TECHNOLOGY, PTS 1-3, 2012, 418-420 : 1494 - +
[47] Mechanical properties of HA/316L stainless steel symmetrical functionally gradient biocomposites
Fan, Xin
Zou, Jian-Peng
Wan, Qian
Chen, Jian
Zhou, Zhong-Cheng
Ruan, Jian-Ming
Zhongnan Daxue Xuebao (Ziran Kexue Ban)/Journal of Central South University (Science and Technology), 2009, 40 (03): : 632 - 637
[48] Structural, mechanical and tribological properties of Ti and TiN coatings on 316L stainless steel
Yazici, M.
Kovaci, H.
Yetim, A. F.
Celik, A.
CERAMICS INTERNATIONAL, 2018, 44 (12) : 14195 - 14201
[49] Effect of High Laser Energy Density on Selective Laser Melted 316L Stainless Steel: Analysis on Metallurgical and Mechanical Properties and Comparison with Wrought 316L Stainless Steel
Shanmuganathan, Pradeep Kumar
Purushothaman, Dinesh Babu
Ponnusamy, Marimuthu
3D PRINTING AND ADDITIVE MANUFACTURING, 2023, 10 (03) : 383 - 392
[50] Effect of High Laser Energy Density on Selective Laser Melted 316L Stainless Steel: Analysis on Metallurgical and Mechanical Properties and Comparison with Wrought 316L Stainless Steel
Shanmuganathan, Pradeep Kumar
Purushothaman, Dinesh Babu
Ponnusamy, Marimuthu
3D PRINTING AND ADDITIVE MANUFACTURING, 2021,

← 1 2 3 4 5 →