Slipcasting of MAX phase tubes for nuclear fuel cladding applications

被引：16

作者：

Galvin, T. ^{[1
]}

Hyatt, N. C. ^{[1
]}

Rainforth, W. M. ^{[1
]}

Reaney, I. M. ^{[1
]}

Shepherd, D. ^{[2
]}

机构：

[1] Univ Sheffield, Dept Mat Sci & Engn, Sir Robert Hadfield Bldg,Mappin St, Sheffield S1 3JD, S Yorkshire, England

[2] NNL, NNL Preston Lab, Preston PR4 0XJ, Lancs, England

来源：

NUCLEAR MATERIALS AND ENERGY | 2020年 / 22卷

基金：

英国工程与自然科学研究理事会;

关键词：

MAX phase; Slipcast; Nuclear fuel; Clad; Ti3SiC2; NEUTRON-IRRADIATION; TI3SIC2; TI3ALC2; TI2ALC; OXIDATION; CORROSION; EVOLUTION; BEHAVIOR; CR2ALC;

D O I：

10.1016/j.nme.2020.100725

中图分类号：

TL [原子能技术]; O571 [原子核物理学];

学科分类号：

0827 ; 082701 ;

摘要：

As a proof of concept, tubes of Ti3SiC2 MAX phase were slipcast in order to investigate its potential for the fabrication of fuel cladding for nuclear reactors. A slip consisting of 46% dry weight basis (dwb) water, 4% dwb polyethyleneimine (PEI), 0.5% dwb methylcellulose was used to cast the tubes, which were then sintered for 2 h under vacuum at 1450 degrees C. Silicon loss was observed at surface which resulted in the formation of TiC. The hoop stress to destruction of the tubes was measured and achieved a maximum of 9.1 +/- 2.2 MPa/mm of tube thickness.

引用

页数：8

共 50 条

[41] AXIAL CRACK-PROPAGATION IN FUEL PIN CLADDING TUBES
FORD, IJ
NUCLEAR ENGINEERING AND DESIGN, 1992, 136 (03) : 243 - 254
[42] OPTIMIZED CLADDING TUBES FOR PWR AND BWR FUEL-RODS
GARZAROLLI, F
STEINBERG, E
TRAPPPRITSCHING, S
WEIDINGER, HG
ATOMWIRTSCHAFT-ATOMTECHNIK, 1989, 34 (11): : 545 - 546
[43] MICROSTRUCTURE AND CORROSION-RESISTANCE OF IRRADIATED FUEL CLADDING TUBES
ETOH, Y
JOURNAL OF NUCLEAR SCIENCE AND TECHNOLOGY, 1992, 29 (06) : 589 - 597
[44] Mechanical properties of SiC/SiC braided tubes for fuel cladding
Rohmer, Eric
Martin, Eric
Lorrette, Christophe
JOURNAL OF NUCLEAR MATERIALS, 2014, 453 (1-3) : 16 - 21
[45] Reassessment of oxidation-induced amorphization and dissolution of Nb precipitates in Zr-Nb nuclear fuel cladding tubes
Matsukawa, Y.
Kitayama, S.
Murakami, K.
Shinohara, Y.
Yoshida, K.
Maeno, H.
Yang, H. L.
Toyama, T.
Yasuda, K.
Watanabe, H.
Kimura, A.
Muta, H.
Yamanaka, S.
Li, Y. F.
Satoh, Y.
Kano, S.
Abe, H.
ACTA MATERIALIA, 2017, 127 : 153 - 164
[46] CALCULATION OF NUCLEAR FUEL CLADDING INTERNAL COATING THICKNESS FOR EMERGENCY RESISTANT NUCLEAR FUEL ELEMENT
Hamad, Rofida Hamad Khalifa
Nikitenkov, Nikolai N.
Kudiyarov, Viktor N.
BULLETIN OF THE TOMSK POLYTECHNIC UNIVERSITY-GEO ASSETS ENGINEERING, 2023, 334 (06): : 27 - 34
[47] LENGTH GROWTH OF FUEL RODS WITH ZRY-4 CLADDING TUBES
MANZEL, R
ATOMWIRTSCHAFT, 1972, 17 (11): : 563 - &
[48] TECHNOLOGY OF ZIRCONIUM ALLOYS FOR CLADDING TUBES OF WATER COOLED FUEL ASSEMBLIES
KNODLER, D
RESCHKE, S
WEIDINGER, HG
KERNTECHNIK, 1987, 50 (04) : 255 - 265
[49] The Simulated Damage of Zircaloy Fuel Cladding Tubes with Brittle Hydride Blisters
Chen, Zhengxiang
Cizelj, Leon
Ursic, Mitja
22ND INTERNATIONAL CONFERENCE NUCLEAR ENERGY FOR NEW EUROPE, (NENE 2013), 2013,
[50] ELECTRON BEAM WELDING OF NUCLEAR FUEL CLADDING COMPONENTS
KLEIN, RF
JOURNAL OF THE ELECTROCHEMICAL SOCIETY, 1964, 111 (03) : C70 - C70

← 1 2 3 4 5 →