Effect of Intercritical Heat Treatment on the Abrasive Wear Behaviour of Plain Carbon Dual Phase Steel

被引：0
|
作者：
Manoj, M. K. [1 ]
Pancholi, V. [1 ]
Nath, S. K. [1 ]
机构：
[1] IIT Roorkee, Dept Met Mat Engg, Roorkee, Uttar Pradesh, India
来源：
MICROSTRUCTURE AND TEXTURE IN STEELS AND OTHER MATERIALS | 2009年
关键词：
DP steel; Abrasive wear; Martensite; MICROSTRUCTURE;
D O I：
10.1007/978-1-84882-454-6_34
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
Dual phase (DP) steels have been prepared from low carbon steel (0.14% C) at intercritical temperature 740 degrees C and time is varied from 1 minute to 30 minutes followed by water quenching. These steels have been characterized by optical microscopy, FE-SEM, hardness measurements, tensile properties and electron backscattered diffraction (EBSD) studies. Tensile properties of a typical dual phase steel are found to be 805 MPa ultimate tensile strength with 18% total elongation. Martensite volume fraction of D P steel (determined by EBSD technique) prepared at 740 degrees C for 6 minutes is found to be 10.2% and the grain size of ferrite and martensite found to be 14.39 micron and 1.05 microns respectively. Abrasive wear resistance of dual phase steels has been determined by pin on drum wear testing machine. DP steels have been found to be 25% more wear resistant than that of normalized steel. Short intercritical heating time followed by water quenching gives higher wear resistance by virtue of smaller and well dispersed martensite island in the matrix of ferrite.
引用
收藏
页码：483 / 488
页数：6
相关论文
共 50 条
  • [41] THE TEMPERING BEHAVIOR OF A PLAIN CARBON DUAL-PHASE STEEL
    JOARDER, A
    JHA, JN
    OJHA, SN
    SARMA, DS
    MATERIALS CHARACTERIZATION, 1990, 25 (02) : 199 - 209
  • [42] The effect of microstructure on abrasive wear of steel
    Kesner, A.
    Choteborsky, R.
    Linda, M.
    1ST NOMMENSEN INTERNATIONAL CONFERENCE ON TECHNOLOGY AND ENGINEERING, 2017, 237
  • [43] EFFECT OF MICROSTRUCTURE ON MECHANICAL PROPERTIES AND ABRASIVE WEAR BEHAVIOR OF LOW CARBON DUAL-PHASE STEELS
    Tuzemen, Mehmet Cagri
    Salamci, Elmas
    PROCEEDINGS OF THE ASME 12TH BIENNIAL CONFERENCE ON ENGINEERING SYSTEMS DESIGN AND ANALYSIS - 2014, VOL 3, 2014,
  • [44] ABRASIVE WEAR OF CARBON STEEL AT LOW TEMPERATURES
    KOVALCHU.VA
    RUSSIAN ENGINEERING JOURNAL-USSR, 1967, 47 (02): : 37 - &
  • [45] Effect of intercritical annealing temperature and holding time on microstructure and mechanical properties of dual phase low carbon steel
    Alfirano
    Samdan, Wibawa
    Maulud, Hidayat
    ADVANCES IN APPLIED MECHANICS AND MATERIALS, 2014, 493 : 721 - +
  • [46] Effect of Intercritical Annealing Conditions on Grain Growth Kinetics of Dual Phase Steel
    Fateme Najafkhani
    Hamed Mirzadeh
    Mehran Zamani
    Metals and Materials International, 2019, 25 : 1039 - 1046
  • [47] Effect of heat treatment on the wear resistance of high-carbon and high-nitrogen steels subjected to abrasive wear
    Filippov, M. A.
    Belozerova, T. A.
    Blinov, V. M.
    Kostina, M. A.
    Val'kov, E. V.
    METAL SCIENCE AND HEAT TREATMENT, 2006, 48 (3-4) : 170 - 174
  • [48] Effect of heat treatment on the wear resistance of high-carbon and high-nitrogen steels subjected to abrasive wear
    M. A. Filippov
    T. A. Belozerova
    V. M. Blinov
    M. A. Kostina
    E. V. Val’kov
    Metal Science and Heat Treatment, 2006, 48 : 170 - 174
  • [49] Effect of Intercritical Annealing Conditions on Grain Growth Kinetics of Dual Phase Steel
    Najafkhani, Fateme
    Mirzadeh, Hamed
    Zamani, Mehran
    METALS AND MATERIALS INTERNATIONAL, 2019, 25 (04) : 1039 - 1046
  • [50] INFLUENCE OF DIFFERENT CYCLIC INTERCRITICAL HEATTREATMENT SCHEDULES ON THE MICROSTRUCTURE AND MECHANICAL BEHAVIOUR OF A DUAL PHASE MEDIUM CARBON LOW ALLOY STEEL
    Alaneme, K. K.
    Adejumo, O. J.
    Borode, J. O.
    METALLURGICAL & MATERIALS ENGINEERING, 2013, 19 (02) : 155 - 165
12345