Tribocorrosion behaviour of Ti6A14V in artificial seawater at low contact pressures

被引：30

作者：

Pejakovic, Vladimir ^{[1
]}

Totolin, Vladimir ^{[1
]}

Ripoll, Manel Rodriguez ^{[1
]}

机构：

[1] AC2T Res GmbH, Viktor Kaplan Str 2-C, A-2700 Wiener Neustadt, Austria

来源：

TRIBOLOGY INTERNATIONAL | 2018年 / 119卷

关键词：

Tribocorrosion; Titanium alloy; Roughness; Off-shore; SODIUM-CHLORIDE SOLUTION; STAINLESS-STEEL; ELECTROCHEMICAL TECHNIQUES; CORROSION BEHAVIOR; ALLOYS; TI6AL4V; DEGRADATION; MECHANISMS; COATINGS; SURFACES;

D O I：

10.1016/j.triboint.2017.10.025

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

The tribo-electrochemical performance of Ti6Al4V in artificial seawater is investigated under reciprocating sliding conditions at three contact loads (10 mN, 100 mN, and 1 N) and three electrochemical conditions (-0.5 V, OCP and +0.5 V). The results reveal that the achieved contact pressures are not able to fully depassivate the surface. For the lowest load, no rupture on the passive film could be detected while with an increase in the load, depassivation-repassivation takes place during sliding contact. For 100 mN, an unusual higher coefficient of friction was measured for all electrochemical testing conditions. This behaviour is observed to correlate with a higher synergy between corrosion and wear and seems to be linked with the initial surface roughness of the titanium alloy.

引用

页码：55 / 65

页数：11

共 50 条

[41] A study of mechanical and biological behavior of porous Ti6A14V fabricated on EBM
Petrovic, V.
Blasco, J. R.
Portoles, L.
Morales, I.
Primo, V.
Atienza, C.
Moreno, J. F.
Belloch, V.
INNOVATIVE DEVELOPMENTS ON VIRTUAL AND PHYSICAL PROTOTYPING, 2012, : 115 - 120
[42] Plasma nitriding of Ti6A14V alloy for improved water erosion resistance
Batory, D.
Szymanski, W.
Panjan, M.
Zabeida, O.
Klemberg-Sapieha, J. E.
WEAR, 2017, 374 : 120 - 127
[43] Numerical analyses of molten pool evolution in laser polishing Ti6A14V
Li, Kai
Zhao, Zhenyu
Zhou, Houming
Zhou, Hao
Jin, Jingcheng
JOURNAL OF MANUFACTURING PROCESSES, 2020, 58 : 574 - 584
[44] ELECTROCHEMICAL FABRICATION OF BIOACTIVE COMPOSITE COATINGS ON TI6A14V SURGICAL ALLOY
SHIRKHANZADEH, M
MATERIALS LETTERS, 1992, 14 (01) : 27 - 30
[45] Biological performance of uncoated and octacalcium phosphate-coated Ti6A14V
Habibovic, P
Li, JP
van der Valk, CM
Meijer, G
Layrolle, P
van Blitterswijk, CA
de Groot, K
BIOMATERIALS, 2005, 26 (01) : 23 - 36
[46] Study of the tribocorrosion behaviour of Ti6Al4V-HA biocomposites
Buciumeanu, M.
Araujo, A.
Carvalho, O.
Miranda, G.
Souza, J. C. M.
Silva, F. S.
Henriques, B.
TRIBOLOGY INTERNATIONAL, 2017, 107 : 77 - 84
[47] Influence of a loading direction on the fracture locus of Ti6A14V Titanium alloy
Mocko, Wojciech
DYMAT 23RD TECHNICAL MEETING - INTERNATIONAL CONFERENCE ON DYNAMIC FRACTURE OF DUCTILE MATERIALS, 2017, 197 : 196 - 203
[48] Fatigue limit of Ti6A14V alloy produced by Selective Laser Sintering
Benedetti, M.
Cazzolli, M.
Fontanari, V.
Leoni, M.
21ST EUROPEAN CONFERENCE ON FRACTURE, (ECF21), 2016, 2 : 3158 - 3167
[49] Fast formation of biomimetic Ca-P coatings on Ti6A14V
Barrere, F.
Layrolle, P.
van Blitterswijk, C.A.
de Groot, K.
Materials Research Society Symposium - Proceedings, 2000, 599 : 135 - 140
[50] PREPARATION AND SURFACE SPECTROSCOPIC CHARACTERIZATION OF OXIDE-FILMS ON TI6A14V
ASK, M
LAUSMAA, J
KASEMO, B
APPLIED SURFACE SCIENCE, 1989, 35 (03) : 283 - 301

← 1 2 3 4 5 →