Burr formation in micro-machining aluminum, 6061-T6

被引：0
|
作者：
Lee, K [1 ]
Stirn, B [1 ]
Dornfeld, DA [1 ]
机构：
[1] Univ Calif Berkeley, Dept Mech Engn, Berkeley, CA 94720 USA
来源：
INITIATIVES OF PRECISION ENGINEERING AT THE BEGINNING OF A MILLENNIUM | 2001年
关键词：
burr formation; micro-machining; drilling; milling;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Experimental studies on micro-milling and micro-drilling in aluminum 6061-T6 have been carried out. A range of different cutting speeds, chip loads and depths of cut using a tool of 127 mum diameter were considered. Drilling experiments with different feed to diameter ratios, cutting speeds and two drill diameters were conducted. The influence of the cutting parameters on burr size and burr type was observed. A comparison to burr formation in conventional machining is presented.
引用
收藏
页码：47 / 51
页数：5
相关论文
共 50 条
  • [11] 3D finite element prediction of chip flow, burr formation, and cutting forces in micro end-milling of aluminum 6061-T6
    Davoudinejad, A.
    Parenti, P.
    Annoni, M.
    FRONTIERS OF MECHANICAL ENGINEERING, 2017, 12 (02) : 203 - 214
  • [12] ULTRASONIC STUDIES OF 1060 AND 6061-T6 ALUMINUM
    ASAY, JR
    GUENTHER, AH
    JOURNAL OF APPLIED PHYSICS, 1967, 38 (10) : 4086 - &
  • [13] Fatigue design curves for 6061-T6 aluminum
    Yahr, GT
    JOURNAL OF PRESSURE VESSEL TECHNOLOGY-TRANSACTIONS OF THE ASME, 1997, 119 (02): : 211 - 215
  • [14] RESHOCK AND RELEASE BEHAVIOR OF 6061-T6 ALUMINUM
    ASAY, JR
    CHHABILDAS, LC
    BULLETIN OF THE AMERICAN PHYSICAL SOCIETY, 1980, 25 (04): : 566 - 566
  • [15] DYNAMIC FRACTURE OF 6061-T6 ALUMINUM CYLINDERS
    WESENBERG, DL
    SAGARTZ, MJ
    JOURNAL OF APPLIED MECHANICS-TRANSACTIONS OF THE ASME, 1977, 44 (04): : 643 - 646
  • [16] Numerical Modeling and Experimental Validation in Orthogonal Machining of Aluminum Al 6061-T6 Alloy
    Akram, Sohail
    Uddin, Shafi
    Kazmi, Syed Waqar Haider
    Jaffery, Syed Husain Imran
    Jalil, Mian Aamer
    MEHRAN UNIVERSITY RESEARCH JOURNAL OF ENGINEERING AND TECHNOLOGY, 2020, 39 (01) : 179 - 194
  • [17] Statistical Analysis of Machining Parameters on Burr Formation, Surface Roughness and Energy Consumption during Milling of Aluminium Alloy Al 6061-T6
    Zaidi, Sajid Raza
    Ul Qadir, Najam
    Jaffery, Syed Husain Imran
    Khan, Muhammad Ali
    Khan, Mushtaq
    Petru, Jana
    MATERIALS, 2022, 15 (22)
  • [18] Study on burr formation in micro-machining using micro-tools fabricated by micro-EDM
    Chern, Gwo-Lianq
    Wu, Ying-Jeng Engin
    Cheng, Jyun-Cheng
    Yao, Jian-Cheng
    PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY, 2007, 31 (02): : 122 - 129
  • [19] A Study on Milling Burr Expert System in Micro-Machining
    Zhu Yunming
    Wang Guicheng
    Fan Shutian
    Wang Zhi
    Pei Hongjie
    INTERNATIONAL CONFERENCE ON INTELLIGENT COMPUTATION TECHNOLOGY AND AUTOMATION, VOL 1, PROCEEDINGS, 2008, : 965 - 969
  • [20] MACHINING PERFORMANCE OF ALUMINUM ALLOY 6061-T6 ON SURFACE FINISH USING MINIMUM QUANTITY LUBRICATION
    Najiha, M. S.
    Rahman, M. M.
    Kadirgama, K.
    INTERNATIONAL JOURNAL OF AUTOMOTIVE AND MECHANICAL ENGINEERING, 2015, 11 : 2699 - 2712
12345