Dynamic behavior and a modified Johnson-Cook constitutive model of Inconel 718 at high strain rate and elevated temperature

被引：148

作者：

Wang, Xiangyu ^{[1
,2
]}

Huang, Chuanzhen ^{[1
,2
]}

Zou, Bin ^{[1
,2
]}

Liu, Hanlian ^{[1
,2
]}

Zhu, Hongtao ^{[1
,2
]}

Wang, Jun ^{[1
,2
]}

机构：

[1] Shandong Univ, Ctr Adv Jet Engn Technol CaJET, Sch Mech Engn, Jinan 250061, Peoples R China

[2] Shandong Univ, Minist Educ, Key Lab High Efficiency & Clean Mech Manufacture, Jinan 250061, Peoples R China

来源：

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2013年 / 580卷

关键词：

Inconel; 718; High strain rate; Elevated temperature; Modified Johnson-Cook model; NICKEL-BASED ALLOYS; CHIP FORMATION; RESIDUAL-STRESSES; PREDICTION; SIMULATION;

D O I：

10.1016/j.msea.2013.05.062

中图分类号：

TB3 [工程材料学];

学科分类号：

0805 ; 080502 ;

摘要：

Constitutive model is very important in finite element simulation of Inconel 718 cutting process. However, there are few constitutive models for Inconel 718 which are suitable for the cutting process. In this research, firstly, dynamic behavior of Inconel 718 at high strain rate and elevated temperature of the same order as the practical cutting process was obtained using SHPB(Split Hopkinson Pressure Bar) test. In the tests, the strain rate was 5000-11000 s(-1), and the temperature was 500-800 degrees C. Secondly, thermal and strain rate effect were discussed. Strain rate softening effect was found at high strain rate and discussed, and it was temperature dependent. Finally, a modified Johnson-Cook model was established. (C) 2013 Elsevier B.V. All rights reserved.

引用

页码：385 / 390

页数：6

共 50 条

[41] Method of Finite Element Model Updating for Identifying the Parameters of Modified Johnson-Cook Constitutive Equation
Shin, Dong-Seok
Jeon, Euy-Sik
Kim, Young-Shin
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024,
[42] A modified Johnson-Cook model for dynamic behavior of spray-deposition 17 vol.% SiCp/7055Al composites at high strain rates
Tang, Binbin
Wang, Haitao
Jin, Peipeng
Jiang, Xianquan
MATERIALS RESEARCH EXPRESS, 2020, 7 (05)
[43] Modification of strain rate strengthening coefficient for Johnson-Cook constitutive model of Ti6Al4V alloy
Zhu, Shuisheng
Liu, Jie
Deng, Xin
MATERIALS TODAY COMMUNICATIONS, 2021, 26 (26):
[44] The Comparation of Arrhenius-Type and Modified Johnson-Cook Constitutive Models at Elevated Temperature for Annealed TA31 Titanium Alloy
Yang, Shengli
Liang, Pei
Gao, Fuyang
Song, Dejun
Jiang, Peng
Zhao, Min
Kong, Ning
MATERIALS, 2023, 16 (01)
[45] Strain-rate Relationship of Aluminum Matrix Composites Predicted by Johnson-Cook Model
Zhu DeZhi
Chen WeiPing
Li YuanYuan
PHYSICAL AND NUMERICAL SIMULATION OF MATERIAL PROCESSING VI, PTS 1 AND 2, 2012, 704-705 : 935 - 940
[46] Method for determining the strain rate sensitivity factor for the Johnson-Cook model in Charpy tests
Stopel, Michal
Skibicki, Dariusz
Mocko, Wojciech
MATERIALS TESTING, 2017, 59 (11-12) : 965 - 973
[47] Modified Johnson-Cook model of aluminum alloy 6016-T6 sheets at low dynamic strain rates
Jia, Zhe
Guan, Ben
Zang, Yong
Wang, Yuan
Mu, Lei
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2021, 820 (820):
[48] Flow Behavior of 20CrMnTiH Steel Studied by Modified Johnson-Cook Model
Chai, Rong Xia
Guo, Wei
Guo, Cheng
MANUFACTURING, DESIGN SCIENCE AND INFORMATION ENGINEERING, VOLS I AND II, 2015, : 743 - 747
[49] Calibration and Verification of Dynamic Mechanical Properties of High-strength Armored Steel Based on Johnson-Cook Constitutive Model
Zhang D.
Zhao Z.
He L.
Ren J.
Qiang L.
Zhou Y.
Binggong Xuebao/Acta Armamentarii, 2022, 43 (08): : 1966 - 1976
[50] A modified Johnson Cook model for elevated temperature flow behavior of T24 steel
Li, Hong-Ying
Wang, Xiao-Feng
Duan, Jun-Ying
Liu, Jiao-Jiao
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2013, 577 : 138 - 146

← 1 2 3 4 5 →