Deep hole drilling using tools with small diameters-Process analysis and process design

被引：37

作者：

Zabel, Andreas ^{[1
]}

Heilmann, Markus ^{[1
]}

机构：

[1] TU Dortmund Univ, Inst Machining Technol, Dortmund, Germany

来源：

CIRP ANNALS-MANUFACTURING TECHNOLOGY | 2012年 / 61卷 / 01期

关键词：

Drilling; Tool geometry; Laser;

D O I：

10.1016/j.cirp.2012.03.002

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This paper is focused on the drilling of bore holes with high length-to-diameter ratios and diameters less than 2 mm which are needed, for example, in medical and automotive applications. In the presented research, the influence of cutting data and tool design on tool wear and chip formation has been analysed. First the experimental set-up is described followed by an in-depth process analysis of the single-lip deep hole drilling process under investigation. The next section deals with a process combination, where laser and mechanical drilling are combined in order to improve process reliability and productivity. (C) 2012 CIRP.

引用

页码：111 / 114

页数：4

共 50 条

[1] Analysis of the Laser Drilling Process for the Combination with a Single-Lip Deep Hole Drilling Process with Small Diameters
Biermann, Dirk
Heilmann, Markus
LASERS IN MANUFACTURING 2011: PROCEEDINGS OF THE SIXTH INTERNATIONAL WLT CONFERENCE ON LASERS IN MANUFACTURING, VOL 12, PT B, 2011, 12 : 308 - 316
[2] Process adapted structure optimization of deep hole drilling tools
Biermann, D.
Kersting, M.
Kessler, N.
CIRP ANNALS-MANUFACTURING TECHNOLOGY, 2009, 58 (01) : 89 - 92
[3] Small hole drilling process
不详
AIRCRAFT ENGINEERING AND AEROSPACE TECHNOLOGY, 2005, 77 (05): : 432 - 433
[4] Bifurcations of Deep Hole Drilling Process
Bykador, V. S.
Bykador , Zh. E.
INTERNATIONAL CONFERENCE ON INDUSTRIAL ENGINEERING (ICIE 2017), 2017, 206 : 151 - 156
[5] Dynamic Modelling and Analysis of Deep-Hole Drilling Process
Int J Modell Simul, 3 (157):
[6] Small deep hole drilling electro discharge machining process optimization using Taguchi method
Jimenez-Chavarro, Guillermo
Jose Vieira-Porto, Arthur
Hideaki-Tsunaki, Roberto
REVISTA FACULTAD DE INGENIERIA, UNIVERSIDAD PEDAGOGICA Y TECNOLOGICA DE COLOMBIA, 2016, 25 (42): : 111 - 122
[7] A novel method for chip formation analyses in deep hole drilling with small diameters
Biermann D.
Kirschner M.
Eberhardt D.
Kirschner, M. (kirschner@isf.de), 1600, Springer Verlag (08): : 491 - 497
[8] Modelling of dynamic system characteristics of deep hole drilling process with tools about flexible stifness
Zubrzycki, Jaroslaw
Swic, Antoni
Opielak, Marek
INDUSTRIAL AND SERVICE ROBOTICS, 2014, 613 : 333 - 339
[9] Study on deep hole drilling process and cutting performance
You F.Q.
Zhang R.
Wang Y.G.
Key Engineering Materials, 2020, 866 : 42 - 53
[10] The investigation on the machining process of BTA deep hole drilling
Gao, CH
Cheng, K
Kirkwood, D
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2000, 107 (1-3) : 222 - 227

← 1 2 3 4 5 →