Analysis of Effect of Process Parameters on Warpage of a automobile bumper injection molded parts

被引：1
|
作者：
Wu, Shuting [1 ]
Liu, Hongbin [1 ]
Wu, Haitao [1 ]
机构：
[1] Kunming Univ Sci & Technol, Fac Mech & Elect Engn, Kunming, Peoples R China
来源：
ADVANCES IN MATERIALS AND MATERIALS PROCESSING, PTS 1-3 | 2013年 / 652-654卷
关键词：
warpage; process parameters; numerical simulation; OPTIMIZATION;
D O I：
10.4028/www.scientific.net/AMR.652-654.2062
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Take a automobile bumper for example, analysis of effect of process parameters on warpage of a automobile bumper, including melt temperature, injection time, cooling time and packing pressure, on the warpage of the automobile bumper were analyzed by means of Moldflow software. The results show the warpage decrease of the increase of the injection time, the cooling time and the packing pressure, but when the packing pressure reached 45MPa, the warpage slightly increased; the melt temperature should be picked out by the characteristics of the plastics material.
引用
收藏
页码：2062 / 2066
页数：5
相关论文
共 50 条
  • [21] Numerical simulation and experimental study of warpage of injection-molded parts
    Zhou, HM
    Li, DQ
    POLYMER-PLASTICS TECHNOLOGY AND ENGINEERING, 2005, 44 (04) : 603 - 617
  • [22] Minimization of Warpage for Injection Molded Parts by Inverse Thermal Mold Design
    Hopmann, Ch.
    Nikoleizig, P.
    Dornebusch, H.
    Schneppe, T.
    INTERNATIONAL POLYMER PROCESSING, 2018, 33 (01) : 110 - 116
  • [23] Application of soft computing for the prediction of warpage of plastic injection molded parts
    Reddy, B. Sidda
    Kumar, J. Suresh
    Reddy, Vijaya Kumar
    Padmanabhan, G.
    Journal of Engineering Science and Technology Review, 2009, 2 (01) : 56 - 62
  • [24] Effects of Injection Process Parameters on the Warpage of Thin-walled Plastic Parts
    Sandu, Ionut-Laurentiu
    Fetecau, Catalin
    MATERIALE PLASTICE, 2011, 48 (04) : 315 - 321
  • [25] Effects of Polymer-Filler Properties on the Warpage of Injection Molded Automobile Door
    Liao, Qiuhui
    Zhang, Xiaoxun
    Ruan, Qinchao
    ADVANCED MATERIALS, PTS 1-4, 2011, 239-242 : 2511 - 2514
  • [26] Effect of injection parameters on warpage and sink index of high-gloss injection parts
    Li, X. (lxp2010@zjnu.cn), 1600, Trans Tech Publications Ltd (621):
  • [27] AN ANALYSIS OF THERMAL WARPAGE IN INJECTION MOLDED FLAT PARTS DUE TO UN-BALANCED COOLING
    STJACQUES, M
    POLYMER ENGINEERING AND SCIENCE, 1982, 22 (04): : 241 - 247
  • [28] Analysis of Cavity Pressure and Warpage of Polyoxymethylene Thin Walled Injection Molded Parts: Experiments and Simulations
    Guerrier, P.
    Tosello, G.
    Hattel, J. H.
    PROCEEDINGS OF PPS-30: THE 30TH INTERNATIONAL CONFERENCE OF THE POLYMER PROCESSING SOCIETY, 2015, 1664
  • [29] Structural analysis, process simulation and warpage calculation for the gas-assisted injection molded parts using a unified CAE model
    Chen, SC
    Hu, SY
    Jong, WR
    Jeng, MC
    ANTEC'97 - PLASTICS SAVING PLANET EARTH, CONFERENCE PROCEEDINGS, VOLS 1 - 3, 1997, : 620 - 624
  • [30] Prediction of process-induced warpage in injection molded thermoplastics
    Akay, M
    Ozden, S
    Tansey, T
    POLYMER ENGINEERING AND SCIENCE, 1996, 36 (13): : 1839 - 1846
12345