Behavior of oxygen and carbon in ball-milled Si3N4 powders during heat treatment and sintering

被引：4
|
作者：
Wada, S
Kondo, Y
Sudo, E
Maki, Y
机构：
[1] Toyota Cent Res & Dev Labs Inc, Nagakute, Aichi 4801192, Japan
[2] Shin Etsu Chem Co Ltd, Gunma 3790133, Japan
来源：
JOURNAL OF THE CERAMIC SOCIETY OF JAPAN | 1999年 / 107卷 / 07期
关键词：
silicon nitride; oxygen; carbon; ball milling; ethanol;
D O I：
10.2109/jcersj.107.611
中图分类号：
TQ174 [陶瓷工业]; TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
Three kinds of Si3N4 powders, DW, TX and E10, with and without sintering additives were ball-milled using ethanol as medium. Oxygen and carbon contents in the mixed powders increased due to the mechanochemical reaction between the powders and ethanol. The increases of oxygen and carbon were almost the same for the three powders. After heat treatment at 800-1200 degrees C in vacuum or nitrogen gas, most of the carbon was desorbed. On the other hand, the increment of oxygen remained in the ceramic body even after sintering at 1750 degrees C.
引用
收藏
页码：611 / 614
页数：4
相关论文
共 50 条
  • [41] Pressureless sintering of Si3N4 powders obtained from carbothermally reduced sepiolite
    Kurt, AO
    Davies, TJ
    JOURNAL OF MATERIALS SCIENCE LETTERS, 2001, 20 (11) : 1067 - 1070
  • [42] Effect of ball-milled MgO and Si3N4 addition on the physical, mechanical and thermal behaviour of aluminium based composite developed by hybrid casting technique
    Dwivedi, Shashi Prakash
    INTERNATIONAL JOURNAL OF CAST METALS RESEARCH, 2020, 33 (01) : 35 - 49
  • [43] Increase of oxygen content in Si3N4 powder during ball milling using alcohol as solvent
    Wada, Shigetaka
    Nippon Seramikkusu Kyokai Gakujutsu Ronbunshi/Journal of the Ceramic Society of Japan, 1996, 104 (1215): : 1085 - 1087
  • [44] Increase of oxygen content in Si3N4 powder during ball milling using alcohol as solvent
    Wada, S
    JOURNAL OF THE CERAMIC SOCIETY OF JAPAN, 1996, 104 (11) : 1085 - 1087
  • [45] STABILITY OF SI3N4 AND LIQUID PHASE(S) DURING SINTERING
    GRESKOVICH, C
    PROCHAZKA, S
    JOURNAL OF THE AMERICAN CERAMIC SOCIETY, 1981, 64 (07) : C96 - C97
  • [46] COMPARISON OF CONTINUOUS SINTERING TO BATCH SINTERING OF SI3N4
    WITTMER, DE
    MILLER, CW
    AMERICAN CERAMIC SOCIETY BULLETIN, 1991, 70 (09): : 1519 - 1527
  • [47] SiC Ceramic-Bonded Carbon Fabricated With Si3N4 and Carbon Powders
    Chen, Weiwu
    Tojo, Tetsuro
    Miyamoto, Yoshinari
    INTERNATIONAL JOURNAL OF APPLIED CERAMIC TECHNOLOGY, 2012, 9 (02) : 313 - 321
  • [48] Preparation of α-Si3N4 nanorods assembled nanobelts by crystallizing amorphous Si3N4 powders
    Hu, Zunlan
    Huo, Wenlong
    Zhu, Tianbin
    Liu, Jian
    Xie, Zhipeng
    PHYSICA E-LOW-DIMENSIONAL SYSTEMS & NANOSTRUCTURES, 2019, 112 : 137 - 141
  • [49] Low temperature heat capacity measurements of β-Si3N4 and γ-Si3N4: Determination of the equilibrium phase boundary between β-Si3N4 and γ-Si3N4
    Nishiyama, Norimasa
    Kitani, Suguru
    Ohta, Yuki
    Kulik, Eleonora
    Netriova, Zuzana
    Holzheid, Astrid
    Lences, Zoltan
    Kawaji, Hitoshi
    Wakai, Fumihiro
    JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2020, 40 (16) : 6309 - 6315
  • [50] Synthesis of α-Si3N4 whiskers or equiaxed particles from amorphous Si3N4 powders
    Hu, Zunlan
    Liu, Jian
    Xie, Zhipeng
    CERAMICS INTERNATIONAL, 2020, 46 (15) : 23734 - 23741
12345