Process conditions optimization in Al-Cu alloy matrix composites

被引：38

作者：

Mazahery, Ali ^{[1
]}

Shabani, Mohsen Ostad ^{[1
]}

机构：

[1] Islamic Azad Univ, Lenjan Branch, Dept Mat Sci, Esfahan, Iran

来源：

POWDER TECHNOLOGY | 2012年 / 225卷

关键词：

Aluminum matrix; Iterative algorithm; Analytical methods; CAST A356 ALLOY; MECHANICAL-PROPERTIES; TRIBOLOGICAL PROPERTIES; WEAR BEHAVIOR; ALUMINUM-ALLOYS; BORON-CARBIDE; MICROSTRUCTURE; POROSITY;

D O I：

10.1016/j.powtec.2012.03.039

中图分类号：

TQ [化学工业];

学科分类号：

0817 ;

摘要：

Based on the idea of survival of the fittest and natural selection. a class of parallel iterative algorithm with specific learning ability was introduced to find the optimal solidification conditions and produce 2024 Al alloy with minimum wear and maximum strength. This novel algorithm repeats evaluation, selection, crossover and mutation after initialization until the stopping condition is satisfied. Mechanical and wear properties of unreinforced 2024 Al alloy and composites with different vol.% of coated boron carbide particles were also experimentally investigated. It is seen that incorporation of hard particles to 2024 aluminum alloy contributes to the improvement of the mechanical properties and wear resistance of the base alloy to a great extent. (C) 2012 Elsevier B.V. All rights reserved.

引用

页码：101 / 106

页数：6

共 50 条

[31] Enhanced precipitation hardening in an alumina reinforced Al-Cu alloy matrix composite
Yu, Peng
Kwok, C. K.
To, C. Y.
Li, T. K.
Ng, Dickon H. L.
COMPOSITES PART B-ENGINEERING, 2008, 39 (02) : 327 - 331
[32] Study on the chemical reactions in situ processing α-Al2O3 particle reinforced Al-Cu alloy matrix composites
Chen, Gang
Zhu, Zhengang
Sun, Guoxiong
Jinshu Xuebao/Acta Metallurgica Sinica, 1998, 34 (05): : 531 - 537
[33] MICROSTRUCTURAL EVALUATION OF ZrC REINFORCED Al-Cu MATRIX ALLOY COMPOSITES FABRICATED BY MECHANICAL ALLOYING AND VACUUM HOT PRESSING
Kaftelen, Hulya
Unlu, Necip
Ovecoglu, M. Lutfi
Henein, Hani
TMS 2010 139TH ANNUAL MEETING & EXHIBITION - SUPPLEMENTAL PROCEEDINGS, VOL 2: MATERIALS CHARACTERIZATION, COMPUTATION AND MODELING AND ENERGY, 2010, : 189 - +
[34] Crystallization of droplets in pure Al and Al-Cu alloy
Takada, Y
Kudoh, M
Noguchi, T
MATERIALS TRANSACTIONS JIM, 2001, 42 (02): : 215 - 219
[35] Comparison of the corrosion resistance of an Al-Cu alloy and an Al-Cu-Li alloy
Milagre, Mariana X.
Donatus, Uyime
Machado, Caruline S. C.
Araujo, Joao Victor S.
da Silva, Rejane Maria P.
de Viveiros, Barbara Victoria G.
Astarita, Antonello
Costa, Isolda
CORROSION ENGINEERING SCIENCE AND TECHNOLOGY, 2019, 54 (05) : 402 - 412
[36] THE EFFECT OF VARIOUS PROCESSING CONDITIONS ON THE TEXTURE DEVELOPMENT IN EXTRUDED AL-CU COMPOSITES
GERTELKLOOS, H
BROKMEIER, HG
RITTER, C
ZEITSCHRIFT FUR METALLKUNDE, 1994, 85 (08): : 603 - 608
[37] Distribution of SiCp in Al and Al-Cu alloy centrifugally
Zhang, WQ
Shi, HF
Fu, HM
JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2004, 20 (04) : 448 - 450
[38] Effects of different pouring conditions on the micro-structure of Al-Cu alloy
Shandong Institute of Architecture and Engineering, Ji'nan 250101, China
不详
Tezhong Zhuzao Ji Youse Hejin, 2006, 1 (10-12):
[39] Al-Cu approximants in the Al3Cu4 alloy
Dong, C
Zhang, QH
Wang, DH
Wang, YM
EUROPEAN PHYSICAL JOURNAL B, 1998, 6 (01): : 25 - 32
[40] Mechanical characterization of Al-Cu alloy produced using conventional sintering process
Manjunath, K. N.
Krishnappa, G. B.
MATERIALS TODAY-PROCEEDINGS, 2018, 5 (01) : 3019 - 3026

← 1 2 3 4 5 →