Study on dynamic strength model of contact layer in quick-point grinding

被引：16
|
作者：
Xiu, SC [1 ]
Cai, GQ [1 ]
Li, CH [1 ]
机构：
[1] Northeastern Univ, Sch Mech Engn & Automat, Shenyang 110004, Peoples R China
来源：
ADVANCES IN GRINDING AND ABRASIVE TECHNOLOGY XIII | 2006年 / 304-305卷
关键词：
quick-point grinding; strain rate; impact damage; dynamic strength;
D O I：
10.4028/www.scientific.net/KEM.304-305.570
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Ultra-high grinding speed and point contact are the salient natures of Quick-point grinding. Based on the damage dynamics theory, there are impact damages with a lot of micro-cracks and micro-defects and adiabatic shearing caused by ultra-high strain rate in the contact layer in such grinding manner. The micro-damages are relation to the strain rate and the materials properties, and increase with raise of strain rate. Because of the weakening effect of strain rate, the dynamic strength of the contact layer in Quick-point grinding is decreased and the grinding performance of ductile and brittle materials is also changed. The dynamic strength model of the contact layer in Quick-point grinding was built in this paper, and the weakening effects of strain rate caused by impact micro-damages on the dynamic strength of the layer and the materials removal mechanism in grinding layer were analyzed through the study on the theory and the experiments.
引用
收藏
页码：570 / 574
页数：5
相关论文
共 50 条
  • [21] Research on mechanism of effect on surface roughness with point-grinding angles in quick-point grinding
    Xiu, Shichao
    Gong, Yadong
    Cai, Guangqi
    Zhongguo Jixie Gongcheng/China Mechanical Engineering, 2008, 19 (16): : 1895 - 1897
  • [22] Study on Effect of Grinding Fluid Supply Parameters on Surface Integrity in Quick-point Grinding for Green Manufacturing
    Xiu, S. C.
    Gong, Y. D.
    Cai, G. Q.
    SURFACE FINISHING TECHNOLOGY AND SURFACE ENGINEERING, 2008, 53-54 : 209 - 214
  • [23] Experiment study on residual stresses based on quick-point grinding with vitrified CBN wheel
    Pang, Zirui
    Yuan, Suoxian
    Wang, Wanshan
    Zhu, Chunxia
    ADVANCES IN GRINDING AND ABRASIVE TECHNOLOGY XIV, 2008, 359-360 : 239 - 243
  • [24] Process parameters optima in quick-point grinding ceramics based on the intelligent algorithm
    Zhou, Yunguang
    Ma, Lianjie
    Tan, Yanqing
    Liu, Tao
    Li, Hongyang
    ADVANCES IN MECHANICAL ENGINEERING, 2020, 12 (01)
  • [25] Study on non-interference normal tracking algorithm for NC quick-point grinding of the curve parts
    Luo, Yumei
    Wu, Qi
    Hu, Dejin
    ADVANCES IN MATERIALS MANUFACTURING SCIENCE AND TECHNOLOGY II, 2006, 532-533 : 885 - +
  • [26] On-line error measurement based on CCD in quick-point grinding of curve parts
    Luo, Y. M.
    Hu, D. J.
    E-ENGINEERING & DIGITAL ENTERPRISE TECHNOLOGY, 2008, 10-12 : 812 - 816
  • [27] Research on The Influence of NC Quick-point Grinding Parameters to Complex Rotator Surface Roughness
    Wang, Kai
    Sun, Wanchen
    Nie, Fengming
    Wu, Qingtang
    Wu, Huan
    Li, Shan
    MECHATRONICS ENGINEERING, COMPUTING AND INFORMATION TECHNOLOGY, 2014, 556-562 : 1083 - 1086
  • [28] Experimental investigation on effects of depth of cut on micro-geometric properties in quick-point grinding
    Xiu, Shichao
    Li, Changhe
    Cai, Guangqi
    ADVANCES IN GRINDING AND ABRASIVE TECHNOLOGY XIV, 2008, 359-360 : 103 - +
  • [29] Study on surface roughness model and surface forming mechanism of ceramics in quick point grinding
    Ma, Lianjie
    Gong, Yadong
    Chen, Xiaohui
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2014, 77 : 82 - 92
  • [30] ESTABLISHMENT AND ANALYSIS OF FRACTAL CONTACT MODEL FOR POINT GRINDING PARTS
    Chao, Caixia
    Xiu, Shichao
    Wei, Yongle
    SURFACE REVIEW AND LETTERS, 2023, 30 (02)
12345