Improvement of fatigue properties of Ti-6Al-4V alloy under four-point bending by low temperature nitriding

被引：36

作者：

Kikuchi, Shoichi ^{[1
]}

Yoshida, Sho ^{[2
]}

Ueno, Akira ^{[3
]}

机构：

[1] Shizuoka Univ, Dept Mech Engn, Fac Engn, Naka Ku, 3-5-1 Johoku, Hamamatsu, Shizuoka 4328561, Japan

[2] Ritsumeikan Univ, Grad Sch Sci & Engn, 1-1-1 Noji Higashi, Kusatsu, Shiga 5258577, Japan

[3] Ritsumeikan Univ, Dept Mech Engn, Coll Sci & Engn, 1-1-1 Noji Higashi, Kusatsu, Shiga 5258577, Japan

来源：

INTERNATIONAL JOURNAL OF FATIGUE | 2019年 / 120卷

关键词：

Nitriding; Fatigue; Titanium alloy; Fractography; Fracture mechanics; COMMERCIALLY PURE TITANIUM; WEAR-RESISTANCE; PLASMA; STRENGTH; LAYER; SURFACES; BEHAVIOR; TIME;

D O I：

10.1016/j.ijfatigue.2018.11.005

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

Low temperature nitriding (LTN) was performed for titanium alloy (Ti-6Al-4V) to improve its fatigue properties. A nitrogen compound layer was formed on the surface nitrided at temperatures higher than 873 K, whereas nitrogen diffusion was observed on the surface nitrided at 823 K. Fatigue tests were performed by four-point bending in air under a stress ratio of 0.1. The fatigue limit for Ti-6Al-4V tended to increase with a decrease in the nitriding temperature. LTN at 823 K increased the fatigue limit of Ti-6Al-4V due to the formation of the surface with no nitrogen compound layer and suppression of grain-coarsening.

引用

页码：134 / 140

页数：7

共 50 条

[31] Surface properties of Ti-6Al-4V alloy treated by plasma ion nitriding process
Balasubramanian, K.
Bragadeesvaran, S. R.
Adarsh, S. Ajay
Baranitharan, M.
Gokulakrishnan, K.
MATERIALS TODAY-PROCEEDINGS, 2021, 45 : 957 - 961
[32] Effect of laser gas nitriding on the microstructure and corrosion properties of Ti-6Al-4V alloy
Razavi, Reza Shoja
Salehi, Mehdi
Monirvaghefi, Mahmood
Mozafarinia, Reza
ISIJ INTERNATIONAL, 2007, 47 (05) : 709 - 714
[33] Effect of severe shot peening and ultra-low temperature plasma nitriding on Ti-6Al-4V alloy
Unal, Okan
Maleki, Erfan
Varol, Remzi
VACUUM, 2018, 150 : 69 - 78
[34] Four Point Bending Fatigue Tests of Forged Ti 6Al 4V
Oberwinkler, Bernd
Riedler, Martin
Leitner, Heinz
Javidi, Ataollah
MATERIALS TESTING, 2009, 51 (09) : 580 - 586
[35] Influence of microstructure on fatigue crack propagation under bending in the alloy Ti-6Al-4V after heat treatment
Rozumek, D.
Hepner, M.
MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2015, 46 (11) : 1088 - 1095
[36] Ion nitriding of a commercially pure titanium alloy and of a Ti-6Al-4V
Fare, S.
Lecis, N.
Vedani, M.
Vimercati, G.
Silipigni, A.
Corti, D.
Favoino, P.
METALLURGIA ITALIANA, 2010, (06): : 13 - 18
[37] Effect of Thermodiffusion Nitriding on Cytocompatibility of Ti-6Al-4V Titanium Alloy
Pohrelyuk, I. M.
Tkachuk, O. V.
Proskurnyak, R. V.
Boiko, N. M.
Kluchivska, O. Yu.
Stoika, R. S.
JOM, 2016, 68 (04) : 1109 - 1115
[38] Effect of Thermodiffusion Nitriding on Cytocompatibility of Ti-6Al-4V Titanium Alloy
I. M. Pohrelyuk
O. V. Tkachuk
R. V. Proskurnyak
N. M. Boiko
O. Yu. Kluchivska
R. S. Stoika
JOM, 2016, 68 : 1109 - 1115
[39] The importance of preheat before laser nitriding a Ti-6Al-4V alloy
Hu, C
Baker, TN
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1999, 265 (1-2): : 268 - 275
[40] CHARACTERIZATION OF TI-6AL-4V ALLOY MODIFIED BY PLASMA NITRIDING PROCESS
Bhaysar, Vaibhav N.
Jha, Jyoti Shankar
Jhala, Ghanshyamsinh
Joseph, Alphonsa
Mishra, Sushi
Tewari, Asim
PROCEEDINGS OF THE ASME GAS TURBINE INDIA CONFERENCE, 2017, VOL 2, 2018,

← 1 2 3 4 5 →