Innovative fabrication of porous titanium coating on titanium by cold spraying and vacuum sintering

被引：56
|
作者：
Sun, Jifeng [1 ]
Han, Yong [1 ]
Cui, Kai [1 ]
机构：
[1] Xian Jiaotong Univ, State Key Lab Mech Behavior Mat, Xian 710049, Peoples R China
来源：
MATERIALS LETTERS | 2008年 / 62卷 / 21-22期
关键词：
porous titanium coating; cold spray; bond strength; structure; mechanical properties;
D O I：
10.1016/j.matlet.2008.04.011
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
A porous titanium coating on titanium is fabricated by cold spraying "Mg+Ti" powders followed by vacuum sintering. The porous coating is interconnected, possesses the porosity of 48.6% with pore sizes in the range of 70-150 mu m, and firmly bonds to titanium substrate with a bond strength higher than 42 MPa. The bending Young's modulus and bending strength of the porous coating are 14.47 +/- 1.21 GPa and 106.93 +/- 10.79 MPa, respectively. The compressive Young's modulus and compressive yield strength of the porous coating are 3.99 +/- 0.12 GPa and 178.66 +/- 13.20 MPai, respectively. The porous titanium coating has sufficient strength and matched Young's modulus with nature natural bone for clinical use under load bearing conditions. (c) 2008 Elsevier B.V. All rights reserved.
引用
收藏
页码：3623 / 3625
页数：3
相关论文
共 50 条
  • [1] Preparation and Characterization of Porous Titanium and Titanium Alloy by Cold Spraying
    Li Wenya
    Liao, Hanlin
    Coddet, C.
    RARE METAL MATERIALS AND ENGINEERING, 2009, 38 : 260 - 263
  • [2] Preparation of bioactive and porous titanium coating by vacuum plasma spraying and chemical treatment
    Shi, JM
    Ding, CX
    Wu, XQ
    THERMAL SPRAY 2001: NEW SURFACES FOR A NEW MILLENNIUM, 2001, : 593 - 597
  • [3] Deposition characteristics of titanium coating in cold spraying
    Li, CJ
    Li, WY
    SURFACE & COATINGS TECHNOLOGY, 2003, 167 (2-3): : 278 - 283
  • [4] Innovative fabrication of Ti-48Al-6Nb porous coating by cold gas spraying and reactive sintering
    Yang, Fan
    Lin, Junpin
    He, Yuehui
    Du, Hao
    Chen, Guoliang
    MATERIALS LETTERS, 2012, 76 : 190 - 193
  • [5] Characterization of Porous Titanium-Hydroxyapatite Composite Biological Coating on Polyetheretherketone (PEEK) by Vacuum Plasma Spraying
    Hu, Fengfan
    Fan, Xiujuan
    Peng, Feng
    Yan, Xingchen
    Song, Jinbing
    Deng, Chunming
    Liu, Min
    Zeng, Dechang
    Ning, Chengyun
    COATINGS, 2022, 12 (04)
  • [6] The Effect of Vacuum Leak Rate on Sintering of Porous Titanium Scaffold
    Valanezhad, Alireza
    Savabi, Omid
    Nejatidanesh, Farahnaz
    Khodaei, Mohammad
    Shirani, Mohammad Javad
    Watanabe, Ikuya
    E-JOURNAL OF SURFACE SCIENCE AND NANOTECHNOLOGY, 2019, 17 : 184 - 188
  • [7] Investigation on particles reinforced titanium matrix composite coating fabricated by cold spraying
    State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi'an 710072, China
    不详
    Cailiao Gongcheng, 2013, 4 (1-5+11):
  • [8] Microstructure and Properties of Porous Titanium Materials Fabricated by Cold Pressing and Low-Temperature Vacuum and Hydrogen Sintering
    Senkevich, K. S.
    Pozhoga, O. Z.
    Chernyshova, A. A.
    Serov, M. M.
    RUSSIAN METALLURGY, 2024, 2024 (05): : 1097 - 1104
  • [9] Fabrication of porous titanium scaffolds by stack sintering of microporous titanium spheres produced with centrifugal granulation technology
    Chen, Hongjie
    Wang, Chunli
    Zhu, Xiangdong
    Zhang, Kai
    Fan, Yujiang
    Zhang, Xingdong
    MATERIALS SCIENCE & ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS, 2014, 43 : 182 - 188
  • [10] Sintering of Titanium in Vacuum by Microwave Radiation
    Luo, S. D.
    Yan, M.
    Schaffer, G. B.
    Qian, M.
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2011, 42A (08): : 2466 - 2474
12345