High Temperature Ablation of Composite Material under Plasma Jet Impact

被引:7
|
作者
Levinskas, Rimantas [1 ]
Kezelis, Romualdas [1 ]
Brinkiene, Kristina [1 ]
Grigaitiene, Viktorija [1 ]
Valincius, Vitas [1 ]
Lukosiute, Irena [1 ]
Kavaliauskas, Zydrunas [1 ]
Baltusnikas, Arunas [1 ]
机构
[1] Lithuanian Energy Inst, LT-44403 Kaunas, Lithuania
来源
MATERIALS SCIENCE-MEDZIAGOTYRA | 2011年 / 17卷 / 04期
关键词
plasma jet; protective shell; silicate composite; thermal resistance; ablation; XRD;
D O I
10.5755/j01.ms.17.4.781
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Simulation of the temperature distribution on space vehicles surfaces during its reentry phase is most important for assessing its landing safety. Recently composite materials, produced from high temperature resistance composites are under intensive investigations as surface protective shell for space vehicles during its reentry phases into the atmosphere. The main goal of research is to imitate high aerodynamic heating rates encountered by the protective material during reentry phases of space vehicles. This paper reports the experimental investigations of the new composite material based Oil light silicate frame impregnated by polymer composite tested in high temperature air jet, and generated by means of plasma torch. During experiments the plasma parameters were as follows: plasma torch capacity - (50-70) kW, air flow rate - (19-23) g/s, temperature - (1320-2420)degrees C, velocity - (40-50) m/s. To analyze the effect of the plasma jet impact to protective composite shell, the high speed camera movies were used. Temperature of samples set surface was measured using Type K (chrornel/alumel) thermocouples. Data of composite material ablation rate and temperature of protective sample set surface during experiment are presented.
引用
收藏
页码:423 / 427
页数:5
相关论文
共 50 条
  • [31] Paradox in the Sublimation Mode of the Ablation of Carbon Material in the High-Entalpy Jet of an Aerodynamic Facility
    Gorsky, V. V.
    Dmitrieva, A. A.
    Olenicheva, A. A.
    HIGH TEMPERATURE, 2019, 57 (06) : 904 - 908
  • [32] Paradox in the Sublimation Mode of the Ablation of Carbon Material in the High-Entalpy Jet of an Aerodynamic Facility
    V. V. Gorsky
    A. A. Dmitrieva
    A. A. Olenicheva
    High Temperature, 2019, 57 : 904 - 908
  • [33] On the Formation of a Plasma Cloud at the Ablation of a Pellet in a High-Temperature Magnetized Toroidal Plasma
    Bakhareva, O. A.
    Sergeev, V. Yu.
    Sharov, I. A.
    JETP LETTERS, 2023, 117 (03) : 207 - 213
  • [34] Experimental research on composite material case of SRM under influence of temperature
    Fan, Yu
    Ye, Ding-You
    Shi, Hong-Bin
    Guti Huojian Jishu/Journal of Solid Rocket Technology, 2013, 36 (04): : 539 - 543
  • [35] Transient temperature measurements in a ballistic impact experiment on a thermoplastic composite material
    Savadelis, Alexander I. G.
    Pereira, J. Michael
    Schmidt, Bryan E.
    COMPOSITES PART B-ENGINEERING, 2025, 295
  • [36] Effect of Impact Directions, Fiber Orientation, and Temperature on Composite Material Strength
    Mahmoudi, N.
    Hebbar, A.
    Zenasni, R.
    Lousdad, A.
    JOURNAL OF COMPOSITE MATERIALS, 2009, 43 (16) : 1713 - 1727
  • [37] High-Velocity Impact of Ice Particles on a Composite Material
    Hong, Yun Ky
    Park, Chul
    Baek, Seung Wook
    JOURNAL OF COMPOSITE MATERIALS, 2009, 43 (17) : 1819 - 1834
  • [38] SELF-ABSORPTION OF RADIATION IN A HIGH-TEMPERATURE PLASMA JET
    TAKAI, M
    ARIYASU, T
    ELECTRICAL ENGINEERING IN JAPAN, 1966, 86 (01) : 58 - &
  • [39] Influence of Plasma Jet on Coating Application by High-Temperature Spraying
    Bondareva G.I.
    Toigambaev S.K.
    Kul’chev A.Y.
    Abenov A.T.
    Russian Engineering Research, 2023, 43 (01) : 1 - 5
  • [40] POLYTETRAFLUORO-ETHYLENE ABLATION IN HIGH-TEMPERATURE JET OF DIFFERENT CHEMICAL COMPOSITIONS
    LUIKOV, AV
    SHASHKOV, AG
    YUREVICH, FB
    INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 1969, 12 (05) : 635 - &