On the feasibility of thermoelastic stress analysis on rapid prototyping models

被引：2
|
作者：
Carella, G. [1 ]
Galietti U, U. [1 ]
Modugno, D. [1 ]
机构：
[1] Politecn Bari, DIMeG, I-70126 Bari, Italy
来源：
Advances in Experimental Mechanics IV | 2005年 / 3-4卷
关键词：
thermoelasticity; rapid prototyping; stereolithography (SLA);
D O I：
10.4028/www.scientific.net/AMM.3-4.355
中图分类号：
O3 [力学];
学科分类号：
08 ; 0801 ;
摘要：
This work discusses application of the thermoelastic technique to the stress analysis of Rapid Prototyping (RP) models. The aim is to evaluate the possibility of conducting complete and effective structural tests on prototypes made by means of stereolithography (SLA). The analyzed material is an RP Cure 600 ND epoxy resin. A statistical approach was followed to evaluate the sensitivity of the thermoelastic behaviour of the material to some SLA characteristic parameters. In addition, the effect of load cycle frequency on thermoelastic signal was also analyzed. The experimental work included forty-eight tests on ASTM standardized specimens. A new testing procedure was developed for resin-made models. The new method is based on the application of a loading ramp to SLA standard specimens and on the acquisition of the infrared signal. The thermoelastic constant K is determined using the thermographic signal temporal slope. Results for an engine bracket are presented in the paper.
引用
收藏
页码：355 / 360
页数：6
相关论文
共 50 条
  • [31] Rapid prototyping models for dysplastic hip surgeries in Malaysia
    Dhakshyani, R.
    Nukman, Y.
    Abu Osman, N. A.
    EUROPEAN JOURNAL OF ORTHOPAEDIC SURGERY AND TRAUMATOLOGY, 2012, 22 (01): : 41 - 46
  • [32] Rapid prototyping for hypervelocity impulse facility test models
    Apirana, Steven F. T.
    James, Christopher M.
    Eldridge, Robert
    Morgan, Richard G.
    Lewis, Steven W.
    AEROSPACE SCIENCE AND TECHNOLOGY, 2019, 88 : 174 - 184
  • [33] Using dexels to make hollow models for rapid prototyping
    Chiu, WK
    Tan, ST
    COMPUTER-AIDED DESIGN, 1998, 30 (07) : 539 - 547
  • [34] Computational methods for rapid prototyping of analytic solid models
    Farouki, Rida T.
    Konig, Thomas
    RAPID PROTOTYPING JOURNAL, 1996, 2 (03) : 41 - 48
  • [35] High-level Rapid Prototyping of Graphical Models
    de Villiers, Hendrik
    van Zijl, Lynette
    Niesler, Thomas
    Proceedings of the 2015 Pattern Recognition Association of South Africa and Robotics and Mechatronics International Conference (PRASA-RobMech), 2015, : 130 - 135
  • [36] New rapid prototyping process handles large models
    Designfax Magazine, 1996, 18 (02):
  • [37] Rapid prototyping models for dysplastic hip surgeries in Malaysia
    R. Dhakshyani
    Y. Nukman
    N. A. Abu Osman
    European Journal of Orthopaedic Surgery & Traumatology, 2012, 22 : 41 - 46
  • [38] Volume decomposition of CAD models for rapid prototyping technology
    Chan, CK
    Tan, ST
    RAPID PROTOTYPING JOURNAL, 2005, 11 (04) : 221 - 234
  • [39] Calibration of the thermoelastic constants for quantitative thermoelastic stress analysis on composites
    Salerno, A.
    Costa, A.
    Fantoni, G.
    REVIEW OF SCIENTIFIC INSTRUMENTS, 2009, 80 (03):
  • [40] Inverse analysis related to stress separation in thermoelastic stress analysis
    Kishimoto, K
    Inoue, H
    Shinbo, H
    Shibuya, T
    JSME INTERNATIONAL JOURNAL SERIES A-SOLID MECHANICS AND MATERIAL ENGINEERING, 1997, 40 (02): : 108 - 116
12345