EMISSIONS AND PERFORMANCE ON A JATROPHA OIL METHYL ESTER FUELED DIESEL ENGINE WITH RETARDED INJECTION TIMING

被引:0
|
作者
Suryawanshi, J. G. [1 ]
机构
[1] Visvesvaraya Natl Inst Technol, Dept Mech Engn, Nagpur 440011, Maharashtra, India
关键词
Biodiesel; jatropha oil methyl ester; CI engine; emissions;
D O I
暂无
中图分类号
O414.1 [热力学];
学科分类号
摘要
Injection timing variations have a strong effect on NOx emissions for direct injection diesel engines. Retarded injection is commonly used to control NOx emissions. Biodiesel is a non-toxic, biodegradable and renewable fuel with the potential to reduce engine exhaust emissions. The methyl ester of jatropha oil, known as biodiesel, is receiving increasing attention as an alternative fuel for diesel engines. In the present investigation neat jatropha oil methyl ester (JME) as well as the blends of varying proportions of jatropha oil methyl ester (JME) and diesel were used to run a CI engine with standard injection timing and retarded injection timing. Significant improvements in engine performance and emission characteristics were observed for JME fuel. The addition of JME to diesel fuel has significantly reduced HC, CO, and smoke emissions but it increases the NOX emission slightly with standard injection timing. The NOX emission was decreased with retarded injection timing with negligible effect on fuel consumption rate. Similar trend in brake thermal efficiency and exhaust gas temperature was observed with retarded injection timing while maximum cylinder gas pressure and ignition delay was decreased.
引用
收藏
页数:8
相关论文
共 50 条
  • [1] Influence of Fuel Injection Timing on the Performance and Emission Characteristics of a Diesel Engine Fueled with Jatropha Methyl Ester-Tyre Pyrolysis Oil Blend
    Sharma, Abhishek
    Murugan, S.
    DYNAMICS OF MACHINES AND MECHANISMS, INDUSTRIAL RESEARCH, 2014, 592-594 : 1627 - 1631
  • [2] Combustion analysis of diesel engine fueled with jatropha oil methyl ester - Diesel blends
    Rao, G. Lakshmi Narayana
    Prasad, B. Durga
    Sampath, S.
    Rajagopal, K.
    INTERNATIONAL JOURNAL OF GREEN ENERGY, 2007, 4 (06) : 645 - 658
  • [3] Performance and emission characteristics of a diesel engine fueled with palm, jatropha, and moringa oil methyl ester
    Rashed, M. M.
    Kalam, M. A.
    Masjuki, H. H.
    Mofijur, M.
    Rasul, M. G.
    Zulkifli, N. W. M.
    INDUSTRIAL CROPS AND PRODUCTS, 2016, 79 : 70 - 76
  • [4] Comparative Evaluation of Combustion, Performance, and Emissions of Jatropha Methyl Ester and Karanj Methyl Ester in a Direct Injection Diesel Engine
    Jindal, S.
    Nandwana, Bhagwati P.
    Rathore, Narendra S.
    ENERGY & FUELS, 2010, 24 (03) : 1565 - 1572
  • [5] Effect of Jatropha methyl ester on waste plastic oil fueled DI diesel engine
    Senthilkumar, P.
    Sankaranarayanan, G.
    JOURNAL OF THE ENERGY INSTITUTE, 2016, 89 (04) : 504 - 512
  • [6] Effect of Fuel Injection Timing on the Emissions of a Direct-Injection (DI) Diesel Engine Fueled with Canola Oil Methyl Ester-Diesel Fuel Blends
    Sayin, Cenk
    Gumus, Metin
    Canakci, Mustafa
    ENERGY & FUELS, 2010, 24 (04) : 2675 - 2682
  • [7] Investigation on fuel injection and performance of diesel engine fueled with Jatropha curcas oil
    Luo F.
    Guo J.
    Wang Z.
    Liang Y.
    Jiangsu Daxue Xuebao (Ziran Kexue Ban)/Journal of Jiangsu University (Natural Science Edition), 2011, 32 (03): : 287 - 291
  • [8] Performance and emissions of a diesel tractor engine fueled with marine diesel and soybean methyl ester
    Gokalp, B.
    Buyukkaya, E.
    Soyhan, H. S.
    BIOMASS & BIOENERGY, 2011, 35 (08): : 3575 - 3583
  • [9] Effects of retarded fuel injection timing on combustion and emissions of a diesel engine fueled with canola biodiesel
    Ozturk, Erkan
    Can, Ozer
    Usta, Nazim
    Yucesu, Hueseyin Serdar
    ENGINEERING SCIENCE AND TECHNOLOGY-AN INTERNATIONAL JOURNAL-JESTECH, 2020, 23 (06): : 1466 - 1475
  • [10] EFFECT OF PREHEATED JATROPHA OIL AND JATROPHA OIL METHYL ESTER WITH PRODUCER GAS ON DIESEL ENGINE PERFORMANCE
    Nayak, C.
    Pattanaik, B. P.
    Nayak, S. K.
    INTERNATIONAL JOURNAL OF AUTOMOTIVE AND MECHANICAL ENGINEERING, 2014, 9 : 1709 - 1722