Theory of chain pull-out and stability of weak polymer interfaces .1.

被引:13
|
作者
Kogan, L [1 ]
Hui, CY [1 ]
Ruina, A [1 ]
机构
[1] CORNELL UNIV,DEPT THEORET & APPL MECH,ITHACA,NY 14850
关键词
D O I
10.1021/ma950907v
中图分类号
O63 [高分子化学(高聚物)];
学科分类号
070305 ; 080501 ; 081704 ;
摘要
Polymer/polymer interfaces reinforced with block copolymers or grafted chains can fail by the pull-out of these chains. A number of constitutive models have been proposed in the literature to describe the pull-out of a single chain. In this paper, we use these models to construct a continuum theory of a weak interface, and we study the stability of such an interface subjected to a homogeneous deformation. We show tht if the perturbation contains a Fourier component with wavelength exceeding wa critical value Lambda(c), then the homogeneous deformation is unstable. The dependence of Lambda(c), on the geometry, the stiffness of the material outside the interface, and the pull-out models is derived. We also study the stress field near the tip of a preexisting interface crack using the different pull-out models.
引用
收藏
页码:4090 / 4100
页数:11
相关论文
共 50 条
  • [21] A NEW PULL-OUT TEST FOR TIRE CORD ADHESION .1. HOT BONDING
    ELLUL, MD
    EMERSON, RJ
    RUBBER CHEMISTRY AND TECHNOLOGY, 1988, 61 (02): : 293 - 308
  • [22] Influence of fiber morphology in pull-out process of chain-shaped fiber reinforced polymer composites
    Lu, XL
    Zhang, Y
    Xu, JR
    SCRIPTA MATERIALIA, 2006, 54 (09) : 1617 - 1621
  • [23] ANALYSIS OF THE SINGLE-FIBER PULL-OUT TEST BY THE USE OF RAMAN-SPECTROSCOPY .1. PULL-OUT OF ARAMID FIBERS FROM AN EPOXY-RESIN
    PATRIKIS, AK
    ANDREWS, MC
    YOUNG, RJ
    COMPOSITES SCIENCE AND TECHNOLOGY, 1994, 52 (03) : 387 - 396
  • [24] Stability of fiber spinning under filament pull-out conditions
    van der Walt, C.
    Hulsen, M. A.
    Bogaerds, A. C. B.
    Meijer, H. E. H.
    Bulters, M. J. H.
    JOURNAL OF NON-NEWTONIAN FLUID MECHANICS, 2012, 175 : 25 - 37
  • [25] Interfacial Properties of Carbon-Rubber Interfaces Investigated via Indentation Pull-Out Tests and the JKR Theory
    Li, Zhe
    Yu, Hualong
    Jiang, Bing
    Poldneff, Mike
    Burkhart, Craig
    Liu, Wing K.
    Wang, Q. Jane
    TRIBOLOGY LETTERS, 2013, 52 (01) : 155 - 161
  • [26] A microstructural study of fibre/mortar interfaces during fibre debonding and pull-out
    Geng, Y
    Leung, CKY
    JOURNAL OF MATERIALS SCIENCE, 1996, 31 (05) : 1285 - 1294
  • [27] Simulation of carbon nanotube pull-out when bonded to a polymer matrix
    Frankland, SJV
    Harik, VM
    NANOMATERIALS FOR STRUCTURAL APPLICATIONS, 2003, 740 : 385 - 390
  • [28] A PULL-OUT MODEL FOR PERFECTLY BONDED CARBON NANOTUBE IN POLYMER COMPOSITES
    Ahmed, Khondaker Sakil
    Keng, Ang Kok
    JOURNAL OF MECHANICS OF MATERIALS AND STRUCTURES, 2012, 7 (8-9) : 753 - 764
  • [29] Elastic considerations of field pull-out tests of polymer strip reinforcement
    Konami, T
    Imaizumi, S
    Takahashi, S
    EARTH REINFORCEMENT, VOL 1, 1996, : 57 - 62
  • [30] Effects of pulling velocity and temperature revealed in polymer pull-out simulations
    Bulacu, M.
    van der Giessen, E.
    EPL, 2011, 93 (06)