Effect of laser cladding parameters on Inconel 718 coating performance and multi-parameter optimization

被引:39
|
作者
Xu, Zhenyang [1 ]
Yuan, Junfeng [1 ,2 ,3 ]
Wu, Mingyu [2 ]
Arif, Abul Fazal M. [3 ]
Li, Dongyang [2 ]
机构
[1] China Univ Min & Technol, Sch Mechatron Engn, Xuzhou 221116, Peoples R China
[2] Univ Alberta, Chem & Mat Engn Dept, Edmonton, AB T6G 2H5, Canada
[3] McMaster Univ, McMaster Mfg Res Inst MMRI, Dept Mech Engn, 1280 Main St West, Hamilton, ON L82 4L7, Canada
来源
OPTICS AND LASER TECHNOLOGY | 2023年 / 158卷
基金
中国博士后科学基金;
关键词
Laser cladding; Coating properties; Multi; -response; Parameter optimization; Taguchi method; Grey relational analysis; MECHANICAL-PROPERTIES; RELATIONAL ANALYSIS; STAINLESS-STEEL; CORROSION; MICROSTRUCTURE; ALLOY; WEAR;
D O I
10.1016/j.optlastec.2022.108850
中图分类号
O43 [光学];
学科分类号
070207 ; 0803 ;
摘要
The purpose of this study is to improve the quality of the multi-track laser cladding coating. The Taguchi-Grey relation method was selected to realize process parameter optimization. The Taguchi method is used to design an L16 orthogonal experiment. The influence of three important laser cladding parameters (laser power, powder feeding rate, and scanning speed) on the micro-hardness, maximum load value, yield strength, UTS, and elon-gation had been analyzed based on the analysis of variance (ANOVA) and signal to noise ratio (SNR) methods. The results showed that the yield strength, UTS, and elongation were significantly affected by the laser power; the powder feeding rate denoted a highly significant influence on the microhardness and yield strength; and the scanning speed was a highly significant factor that had an influence on the maximum load value. Then, grey relational analysis (GRA) was used to convert five response targets into a single grey relational grade (GRG) that could be quantified in order to optimize the parameters for maximum micro-hardness, maximum load value, yield strength, UTS, and elongation. Finally, the optimum cladding process parameters were obtained. Through analysis of microstructure, the reduction of the Laves phase might be the main reason for the improvement of coating performance after optimization.
引用
收藏
页数:15
相关论文
共 50 条
  • [31] A MULTI-PARAMETER OPTIMIZATION OF MAMMOGRAPHY
    JAFROUDI, H
    MUNTZ, EP
    JENNINGS, RJ
    BERNSTEIN, H
    AMERICAN JOURNAL OF ROENTGENOLOGY, 1982, 139 (02) : 426 - 426
  • [32] Multi-Parameter Optimization of an Ejector
    N. Poladvandi
    A. H. Aghdam
    Journal of Applied Mechanics and Technical Physics, 2018, 59 : 687 - 692
  • [33] Evaluation of the mechanical properties of Inconel 718 components built by laser cladding
    Tabernero, I.
    Lamikiz, A.
    Martinez, S.
    Ukar, E.
    Figueras, J.
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2011, 51 (06): : 465 - 470
  • [34] Crack analysis and control of laser cladding Inconel718 alloy
    Lu, Yao-Zhong
    Lei, Wei-Ning
    Ren, Wei-Bin
    Chen, Shi-Xin
    Surface Technology, 2020, 49 (09): : 233 - 243
  • [35] Considering cyclic plasticity to predict residual stresses in laser cladding of Inconel 718 multi bead samples
    Ghorashi, Mir Siavash
    Farrahi, Gholam Hossein
    Movahhedy, Mohammad Reza
    JOURNAL OF MANUFACTURING PROCESSES, 2019, 42 : 149 - 158
  • [36] Multi-response multi-parameter optimization of CoCrFeNiMo0.2 HEA coatings prepared by internal laser cladding and tribological behaviors
    Ren, Xiangyu
    Sun, Wenlei
    Gao, Lisha
    Tian, Shuang
    Lin, Hongbo
    MATERIALS TODAY COMMUNICATIONS, 2024, 40
  • [37] Determination of process parameters for selective laser melting of inconel 718 alloy through evolutionary multi-objective optimization
    Tiwari, Jai
    Cozzolino, Ersilia
    Devadula, Sivasrinivasu
    Astarita, Antonello
    Krishnaswamy, Hariharan
    MATERIALS AND MANUFACTURING PROCESSES, 2024, 39 (08) : 1019 - 1028
  • [38] Effect of processing parameters on microstructure of laser solid forming Inconel 718 superalloy
    Zhu, L.
    Xu, Z. F.
    Liu, P.
    Gu, Y. F.
    OPTICS AND LASER TECHNOLOGY, 2018, 98 : 409 - 415
  • [39] Multi-Parameter Optimization and Analysis on Performance of a Mixed Flow Pump
    Wu, X. F.
    Tian, X.
    Tan, M. G.
    Liu, H. L.
    JOURNAL OF APPLIED FLUID MECHANICS, 2020, 13 (01) : 199 - 209
  • [40] Effect of process parameters on the geometry of single-track deposits of Inconel 718 onto AISI4140 using laser cladding
    Momeni, Seyedali
    Coelho, Reginaldo Teixeira
    Nuñez, Johan Grass
    Jasinevicius, Renato Goulart
    International Journal of Advanced Manufacturing Technology, 1600, 134 (11-12): : 5337 - 5353