Effects of Particle Size Distribution of Standard Sands on the Physical-Mechanical Properties of Mortars

被引:7
|
作者
Ferreira, Ruan L. S. [1 ]
Medeiros, Mauriceia [2 ]
Pereira, Jessyca E. S. [2 ]
Henriques, Glauco F. F. [3 ]
Tavares, Jennef C. C. [4 ]
Marvila, Markssuel T. T. [5 ]
de Azevedo, Afonso R. G. [6 ]
机构
[1] Fed Inst Educ Sci & Technol Pernambuco, Civil Construct Dept, BR-55200000 Pesqueira, Brazil
[2] Univ Fed Rio Grande do Norte, Chem Engn Dept, BR-59078970 Natal, Brazil
[3] Univ Fed Paraiba, Grad Program Civil & Environm Engn PPGECAM, Campus 1 Lot Cidade Univ, BR-58051900 Joao Pessoa, Paraiba, Brazil
[4] Fed Rural Univ Semiarid, Sci & Technol Dept, BR-59780000 Caraubas, Brazil
[5] Univ Fed Vicosa, Campus Rio Paranaiba, BR-38810000 Rio Paranaiba, Brazil
[6] UENF State Univ Northern Rio de Janeiro, LECIV Civil Engn Lab, Campos Goytacazes, BR-28013602 Rio De Janeiro, Brazil
关键词
cementitious materials; particle size; granular skeleton; fine aggregate; CEMENT; MICROSTRUCTURE; AGGREGATE; BEHAVIOR; CONSTRUCTION; WASTE;
D O I
10.3390/ma16020844
中图分类号
O64 [物理化学(理论化学)、化学物理学];
学科分类号
070304 ; 081704 ;
摘要
Obtained natural sands can present different particle size distributions (PSD), although they have the same mineralogical origin. These differences directly influence the physical and mechanical behavior of mortars and, therefore, the performance of mortar and ceramic renderings. Standardizing the particle size of sands based on pre-established requirements in normative standards (NBR 7214 or ASTM C778) is one way to minimize these effects. However, these standards do not consider the optimization of the granular skeleton through the analysis of bulk density and PSD, which may be insufficient to obtain satisfactory results. Therefore, this paper analyzes the effects of using different particle size ranges on the physical and mechanical behavior of cement and hydrated lime mortars. The properties of consistency index, bulk density, air content, capillary water absorption, water absorption by immersion, flexural strength, compressive strength, and dynamic modulus of elasticity were evaluated. For this purpose, standardized sands of the same mineralogical origin were made with different particle size ranges, being: (i) standardized sand constituted by 25% of coarse and fine fractions (S25-control), (ii) standardized sand constituted by 30% of coarse fraction and 20% of fine fraction (S30-20), and (iii) standardized sand composed by 40% of coarse fraction, and 10% of fine fraction (S40-10), respectively. The results indicated that variations in the particle size composition of the standardized sands are necessary to obtain mixtures with higher compactness and, therefore, mortars with better physical and mechanical performance. Thus, the dosage of the particle size fractions of standardized sand should consider the optimization of the granular skeleton, being the unit mass and the granulometric composition as important parameters to meet this premise.
引用
收藏
页数:16
相关论文
共 50 条
  • [21] Formaldehyde content and physical-mechanical properties of MUPF-resin-bonded particle materials
    Kehr, E
    Hoferichter, E
    HOLZ ALS ROH-UND WERKSTOFF, 1997, 55 (01) : 34 - 34
  • [22] Effects of grain size distribution and structure on mechanical behavior of silty sands
    Wang Shu-yun
    Lu Xiao-bing
    Shi Zhong-min
    ROCK AND SOIL MECHANICS, 2005, 26 (07) : 1029 - 1032
  • [23] Rheological and mechanical properties of mortars prepared with natural and manufactured sands
    Cortes, D. D.
    Kim, H. -K.
    Palomino, A. M.
    Santamarina, J. C.
    CEMENT AND CONCRETE RESEARCH, 2008, 38 (10) : 1142 - 1147
  • [24] The physical-mechanical properties and biocompatiblity of Biodentine™: A review
    Docimo, R.
    Carrante, V. Ferrante
    Costacurta, M.
    JOURNAL OF OSSEOINTEGRATION, 2021, 13 (01) : 47 - 50
  • [25] PRINCIPLES OF CHANGE IN PHYSICAL-MECHANICAL PROPERTIES OF ROCK
    FILIMONOV, NM
    ABAKOV, GS
    NEFTYANOE KHOZYAISTVO, 1989, (12): : 15 - 17
  • [26] The Effect of Particle Size Distribution on the Physical Properties of Castables
    Samadi, Hamed
    InterCeram: International Ceramic Review, 2003, 52 (05) : 290 - 294
  • [27] Modified Polypropylene with Improved Physical-Mechanical Properties
    Chervakov, D. O.
    Bashtanyk, P. I.
    Burmistr, M. V.
    MECHANICS OF COMPOSITE MATERIALS, 2015, 51 (01) : 93 - 98
  • [28] Physical-mechanical properties of laminated bamboo panels
    Rusch, Fernando
    Trevisan, Romulo
    Hillig, Everton
    Mustefaga, Erick Chagas
    PESQUISA AGROPECUARIA TROPICAL, 2019, 49
  • [29] Evaluation of the physical-mechanical properties of cement-lime based masonry mortars produced with mixed recycled aggregates
    Ferreira, R. L. S.
    Anjos, M. A. S.
    Ledesma, E. F.
    Pereira, J. E. S.
    Nobrega, A. K. C.
    MATERIALES DE CONSTRUCCION, 2020, 70 (337)
  • [30] SYNTHESIS AND PHYSICAL-MECHANICAL PROPERTIES OF POLYPHENYLDIMETHYLSILOXANE FILMS
    ANDRIANO.KA
    ZUBOV, PI
    SUKHAREV.LA
    EMELYANO.VN
    TROENKO, VI
    SMIRNOVA, YP
    KISELEV, MR
    DOKLADY AKADEMII NAUK SSSR, 1971, 197 (03): : 579 - &