Analysis and optimization of the heat affected zone of CFRP by femtosecond laser processing

被引：13

作者：

Chen, Meiling ^{[1
]}

Guo, Baoshan ^{[1
,2
,4
]}

Jiang, Lan ^{[1
,2
,3
]}

Liu, Zhipeng ^{[1
]}

Qian, Qian ^{[1
]}

机构：

[1] Beijing Inst Technol, Sch Mech Engn, Laser Micro Nano Fabricat Lab, Beijing 100081, Peoples R China

[2] Yangtze Delta Reg Acad Beijing Inst Technol, Jiaxing 314019, Peoples R China

[3] Beijing Inst Technol Chongqing Innovat Ctr, Chongqing 401120, Peoples R China

[4] Beijing Inst Technol, Sch Mech Engn, Beijing 100081, Peoples R China

来源：

OPTICS AND LASER TECHNOLOGY | 2023年 / 167卷

基金：

中国国家自然科学基金;

关键词：

Femtosecond laser; CFRP; Ablation threshold; Heat-affected zone; HOLE QUALITY; SINGLE; DAMAGE; COMPOSITES; ABLATION; PHYSICS; TOOL; UV;

D O I：

10.1016/j.optlastec.2023.109756

中图分类号：

O43 [光学];

学科分类号：

070207 ; 0803 ;

摘要：

In this paper, the processing threshold fluence of the carbon fiber reinforced polymers (CFRP) by a femtosecond laser ablating at different scanning speeds is studied, and the effects of processing parameters on the width of the heat-affected zone (HAZ) are discussed. The experimental results show that the ablation threshold of the carbon fiber in CFRP is about two times that of resin at the same scanning speed. At a given scanning speed, the minimum value of HAZ can be obtained when the laser fluence used is 50 similar to 60 times as great as the ablation threshold fluence of the carbon fiber. In addition, the width of the HAZ can be further reduced when the scanning direction is consistent the polarization angle of the linearly polarized laser. The minimum value of the HAZ obtained in the experiment is about 2 mu m, which is much smaller than the value in the previous literature.

引用

页数：8

共 50 条

[21] Probing the heat affected zone by chemical modifications in femtosecond pulse laser ablation of titanium nitride films in air
Bonse, Joern
Krueger, Joerg
JOURNAL OF APPLIED PHYSICS, 2010, 107 (05)
[22] The influence of moisture content on the heat affected zone and the resulting in-plane shear strength of laser cut thermoplastic CFRP
Staehr, R.
Bluemel, S.
Hansen, P.
Jaeschke, P.
Suttmann, O.
Overmeyer, L.
PLASTICS RUBBER AND COMPOSITES, 2015, 44 (03) : 111 - 116
[23] Reducing the taper and heat-affected zone in nanosecond laser drilling of CFRP plate using backside sacrificial layer
Gu, Zehui
He, Yuyang
Ji, Jinghu
Wei, Yifan
Fu, Yonghong
OPTICS AND LASERS IN ENGINEERING, 2025, 185
[24] Optimization methods of hologram for holographic femtosecond laser processing
Hayasaki, Yoshio
Hasegawa, Satoshi
LASER APPLICATIONS IN MICROELECTRONIC AND OPTOELECTRONIC MANUFACTURING (LAMOM) XVI, 2011, 7920
[25] Reduction in heat affected zone and recast layer in laser materials processing using a photon sieve lens
Julian, M. N.
Gupta, M. C.
OPTICS AND LASERS IN ENGINEERING, 2020, 126
[26] Study of die break strength and heat-affected zone for laser processing of thin silicon wafers
Finn, Daragh S.
Lin, Zhibin
Kleinert, Jan
Darwin, Michael J.
Zhang, Haibin
JOURNAL OF LASER APPLICATIONS, 2015, 27 (03)
[27] Research on influence of temporary distribution of power of laser radiation with a hybrid processing on a depth heat affected zone
Bashmakov, D. A.
Israphilov, I. H.
Galiakbarov, A. T.
VI SCIENTIFIC TECHNICAL CONFERENCE ON LOW-TEMPERATURE PLASMA DURING THE DEPOSITION OF FUNCTIONAL COATINGS, 2014, 567
[28] High-Power Laser Cutting of Steel Plates: Heat Affected Zone Analysis
Miraoui, Imed
Boujelbene, Mohamed
Zaied, Mouna
ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2016, 2016
[29] ANALYSIS OF THE HEAT AFFECTED ZONE IN CO2 LASER CUTTING OF STAINLESS STEEL
Madic, Milos J.
Radovanovic, Miroslav R.
THERMAL SCIENCE, 2012, 16 : S363 - S373
[30] ANALYSIS OF HEAT-AFFECTED ZONE FORMATION FOR LASER CUTTING OF STAINLESS-STEEL
SHENG, PS
JOSHI, VS
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1995, 53 (3-4) : 879 - 892

← 1 2 3 4 5 →