Effect of temperature on milling stability of thin-walled parts

被引：6
|
作者：
Liu, Yang [1 ,2 ]
Cui, Ningyuan [1 ]
Chen, Haiyang [1 ]
Yan, Xinxin [1 ]
Zhao, Chencheng [1 ]
Bao, Kuiyuan [1 ]
Shan, Yue [1 ]
Yin, Zijian [1 ]
机构：
[1] Northeastern Univ, Sch Mech Engn & Automat, 11,Lane 3,Wenhua Rd, Shenyang 110819, Liaoning, Peoples R China
[2] Northeastern Univ, Key Lab Vibrat & Control Aeroprop Syst, Minist Educ, Shenyang, Peoples R China
来源：
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE | 2023年 / 237卷 / 03期
基金：
美国国家科学基金会; 中国国家自然科学基金;
关键词：
Thin-walled parts; milling; stability; milling temperature; cutting; TOOL; PREDICTION; SIMULATION; MODEL;
D O I：
10.1177/09544054221101752
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Milling, as a common machining method, is widely used in rough machining and final finishing of various materials. In this paper, according to the milling temperature produced in the milling process, the formula of heat distribution coefficient for workpiece milling is established. By means of Deform-3D finite element software to carry out orthogonal cutting simulation of workpiece, the influence of different machining parameters on milling heat distribution coefficient is studied, the optimal machining parameters are determined, and the milling temperature experiment is carried out to verify the simulation temperature. The experimental results show that the simulation temperature is very close to the experimental workpiece temperature, and the error is very small, which verifies the accuracy of the method. At the same time, the influence of different initial temperature of workpiece on the milling force and stability is also studied. The results show that proper heating of the workpiece can effectively improve the milling stability of the thin-walled parts.
引用
收藏
页码：414 / 423
页数：10
相关论文
共 50 条
  • [31] Investigation on chatter stability of thin-walled parts in milling based on process damping with relative transfer functions
    Liu, Baoguang
    Zhu, Lida
    Dun, Yichao
    Liu, Changfu
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 89 (9-12): : 2701 - 2711
  • [32] Dynamic Models of Stability Lobes of Milling Thin-walled Plates
    Ma, Hailong
    Tang, Aijun
    Chen, Qingkui
    MANUFACTURING SCIENCE AND MATERIALS ENGINEERING, PTS 1 AND 2, 2012, 443-444 : 622 - +
  • [33] Process Stability Strategies in Milling of Thin-walled Inconel 718
    Wanner, B.
    Eynian, M.
    Beno, T.
    Pejryd, L.
    4TH MANUFACTURING ENGINEERING SOCIETY INTERNATIONAL CONFERENCE (MESIC 2011), 2012, 1431 : 465 - 472
  • [34] Stability of micro-milling thin-walled part process
    Jia, Zhenyuan
    Lu, Xiaohong
    Yang, Kun
    Sun, Xvdong
    Liang, Steven Y.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2021, 112 (5-6): : 1529 - 1544
  • [35] Stability of micro-milling thin-walled part process
    Zhenyuan Jia
    Xiaohong Lu
    Kun Yang
    Xvdong Sun
    Steven Y. Liang
    The International Journal of Advanced Manufacturing Technology, 2021, 112 : 1529 - 1544
  • [36] Multi-point Contact Stability Prediction Considering Force-induced Deformation Effect in Milling Thin-Walled Parts
    Wang Z.
    Liu X.
    Li M.
    Wang L.
    Liang S.Y.
    Yu F.
    Jixie Gongcheng Xuebao/Journal of Mechanical Engineering, 2022, 58 (17): : 309 - 320
  • [37] Micro-flank milling forces considering stiffness of thin-walled parts
    Yi, Jie
    Wang, Xibin
    Jiao, Li
    Li, Mingxin
    Xiang, Junfeng
    Yan, Pei
    Chen, Shiqi
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 95 (5-8): : 2767 - 2782
  • [38] Vibratory behavior prediction of thin-walled parts during lateral finish milling
    Lapujoulade, François
    Mabrouki, Tarek
    Raïssi, Kadour
    Mecanique et Industries, 2002, 3 (04): : 403 - 418
  • [39] Analysis of milling surface roughness prediction for thin-walled parts with curved surface
    Yishu Hao
    Yang Liu
    The International Journal of Advanced Manufacturing Technology, 2017, 93 : 2289 - 2297
  • [40] Optimization for cutting force and material removal rate in milling thin-walled parts
    Qu, Sheng
    Zhang, Mingqin
    PROCEEDINGS OF THE 2016 4TH INTERNATIONAL CONFERENCE ON ADVANCED MATERIALS AND INFORMATION TECHNOLOGY PROCESSING (AMITP 2016), 2016, 60 : 461 - 465
12345