Measurement of tritium production in the helium cooled pebble bed test blanket module mock-up at JET during DTE2

被引:0
|
作者
Fonnesu, N. [1 ]
Angelone, M. [1 ]
Loreti, S. [1 ]
Pillon, M. [1 ]
Villari, R. [1 ]
Batistoni, P. [1 ]
Colangeli, A. [1 ]
Flammini, D. [1 ]
Lungaroni, M. [1 ]
Moro, F. [1 ]
Noce, S. [1 ]
Previti, A. [1 ]
Litaudon, X. [2 ]
机构
[1] ENEA, Nucl Dept, Via E Fermi 45, I-00044 Rome, Italy
[2] CEA, IRFM, F-13108 St Paul Les Durance, France
来源
EUROPEAN PHYSICAL JOURNAL PLUS | 2024年 / 139卷 / 10期
关键词
PERFORMANCE;
D O I
10.1140/epjp/s13360-024-05670-6
中图分类号
O4 [物理学];
学科分类号
0702 ;
摘要
Quite often, detectors for measuring nuclear performance and radiation quantities of relevance in fusion experiments are requested to withstand harsh working conditions due to intense neutron and gamma radiation fields. High temperature constitutes a further harsh element in some locations of the machine, where it is necessary to perform some on-line measurements, as expected in the breeding blanket. This is an essential component in future fusion power plants to provide tritium self-sufficiency and its performance must be continuously monitored. Some Test Blanket Modules (TBMs) will be installed in ITER to provide the first experimental data to validate the predictions on tritium production and recovery. In the meantime, within EUROfusion program, the mock-up of the Helium Cooled Pebble Bed Test Blanket Module (HCPB TBM), previously used for the TBM experiment at the Frascati Neutron Generator (FNG), had been installed at JET to test some detectors and for benchmarking numerical codes used for breeding blanket assessment during DTE2 campaign. A diamond detector, calibrated to measure the tritium production through neutron detection inside the HCPB TBM mock-up, was tested during some plasma pulses of the DTE2 campaign at JET. The main outcome is that, as far as neutron emission rate is below 1015 s-1, neutrons are properly detected along the plasma discharge evolution by TBM diamond detector, consistently with the JET neutron monitor KN1. Moreover, the amount of tritium measured (E) is 1.40 x 10-12 tritons per source neutron and the comparison with MCNP radiation transport simulation (C) gives a ratio C/E = 0.77. Such measurements, considered promising, and their comparison with calculations are discussed in the present work. Criticalities emerged are analyzed and some improvements proposed with the main purpose of speeding up signal processing to make the system capable of working at higher plasma neutron emission rates.
引用
收藏
页数:11
相关论文
共 19 条
  • [11] Preliminary Thermo-Hydraulic Analysis of the Breeder Zone for the EU Helium Cooled Pebble Bed Test Blanket Module for ITER
    Neuberger, H.
    Lux, M.
    2009 23RD IEEE/NPSS SYMPOSIUM ON FUSION ENGINEERING, 2009, : 380 - 383
  • [12] HETRA experiment for investigation of heat removal from the first wall of helium-cooled-pebble-bed test blanket module
    Ilic, Milica
    Messemer, Guenter
    Zinn, Kevin
    Kiss, Bela
    FUSION ENGINEERING AND DESIGN, 2011, 86 (9-11) : 2250 - 2253
  • [13] Measurement and analysis of neutron and gamma-ray flux spectra in a neutronics mock-up of the HCPB Test Blanket Module
    Seidel, K.
    Batistoni, P.
    Fischer, U.
    Freiesleben, H.
    Klix, A.
    Leichtle, D.
    Poenitz, E.
    Unholzer, S.
    Villari, R.
    FUSION ENGINEERING AND DESIGN, 2007, 82 (15-24) : 2212 - 2216
  • [14] Experimental and numerical investigations of heat transfer in the first wall of Helium-Cooled-Pebble-Bed Test Blanket Module Part 2: Presentation of results
    Ilic, M.
    Messemer, G.
    Zinn, K.
    Meyder, R.
    Kecskes, S.
    Kiss, B.
    FUSION ENGINEERING AND DESIGN, 2015, 90 : 37 - 46
  • [15] Measurement of tritium production rate in water cooled pebble bed multi-layered blanket mockup by DT neutron irradiation, experiment
    Sato, S.
    Ochiai, K.
    Verzilov, Y.
    Wada, M.
    Kubota, N.
    Kondo, K.
    Yamauchi, M.
    Nishitani, T.
    Konno, C.
    NUCLEAR FUSION, 2007, 47 (07) : 517 - 521
  • [16] TWO DIFFERENT MEDIUM-SCALE FIRST WALL FABRICATION EXPERIMENTS AT KIT FOR ITER HELIUM-COOLED PEBBLE BED TEST BLANKET MODULE
    von der Weth, A.
    Freiner, P.
    Neuberger, H.
    Rey, J.
    FUSION SCIENCE AND TECHNOLOGY, 2012, 62 (01) : 116 - 121
  • [17] Thermal-hydraulic system study of the Helium cooled pebble bed (HCPB) test blanket module (TBM) for ITER using system code RELAP5
    Jin, XZ
    Meyder, R
    PLASMA SCIENCE & TECHNOLOGY, 2005, 7 (02) : 2753 - 2757
  • [18] Thermal-Hydraulic System Study of the Helium Cooled Pebble Bed (HCPB) Test Blanket Module (TBM) for ITER Using System Code RELAP5
    金雪舟
    R.Meyder
    Plasma Science & Technology, 2005, (02) : 2753 - 2757
  • [19] Experimental and numerical investigations of heat transfer in the first wall of Helium-Cooled-Pebble-Bed Test Blanket Module - Part 1: Presentation of test section and 3D CFD model
    Ilic, M.
    Messemer, G.
    Zinn, K.
    Meyder, R.
    Kecskes, S.
    Kiss, B.
    FUSION ENGINEERING AND DESIGN, 2015, 90 : 29 - 36