Predicting the chip flow for nose radius tools under oblique machining conditions

被引：0
|
作者：
Young, Hong-Tsu [1 ]
Liao, Yunn-Shiuan [1 ]
Yang, Yi-Cherng [1 ]
Mathew, Philip [1 ]
机构：
[1] Natl Taiwan Univ, Taipei, Taiwan
来源：
Journal of the Chinese Institute of Engineers, Transactions of the Chinese Institute of Engineers,Series A/Chung-kuo Kung Ch'eng Hsuch K'an | 1993年 / 16卷 / 06期
关键词：
Cutting tools - Machine shop practice - Machining - Turning;
D O I：
10.1080/02533839.1993.9677557
中图分类号：
学科分类号：
摘要：
A model is presented which predicts the chip flow direction for nose radius tools with inclination angles. Experimental verification was made in turning that cut on the bars. A comparison of the predicted and experimental results shows excellent agreement, and the results are consistent with previous findings of other workers.
引用
收藏
页码：825 / 834
相关论文
共 50 条
  • [1] PREDICTION OF CHIP FLOW DIRECTION AND CUTTING FORCES IN OBLIQUE MACHINING WITH NOSE RADIUS TOOLS
    ARSECULARATNE, JA
    MATHEW, P
    OXLEY, PLB
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 1995, 209 (04) : 305 - 315
  • [2] Prediction of tool life in oblique machining with nose radius tools
    Arsecularatne, JA
    Fowle, RF
    Mathew, P
    Oxley, PLB
    WEAR, 1996, 198 (1-2) : 220 - 228
  • [3] Prediction of cutting forces and built-up edge formation conditions in machining with oblique nose radius tools
    Arsecularatne, JA
    Fowle, RF
    Mathew, P
    Oxley, PLB
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 1996, 210 (05) : 457 - 469
  • [4] Cutting force simulation of machining with nose radius tools
    Imani, B. Moetakef
    Yussefian, N. Z.
    2008 INTERNATIONAL CONFERENCE ON SMART MANUFACTURING APPLICATION, 2008, : 19 - 23
  • [5] Upper bound analysis of oblique cutting with nose radius tools
    Adibi-Sedeh, AH
    Madhavan, V
    Bahr, B
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2002, 42 (09): : 1081 - 1094
  • [6] PREDICTING CUTTING FORCES FOR OBLIQUE MACHINING CONDITIONS
    LIN, GCI
    MATHEW, P
    OXLEY, PLB
    WATSON, AR
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS, 1982, 196 (JUN): : 141 - 148
  • [7] ALLOWING FOR NOSE RADIUS EFFECTS IN PREDICTING THE CHIP FLOW DIRECTION AND CUTTING FORCES IN BAR TURNING
    YOUNG, HT
    MATHEW, P
    OXLEY, PLB
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE, 1987, 201 (03) : 213 - 226
  • [8] Upper-bound cutting model for oblique cutting tools with a nose radius
    Seethaler, R.J.
    Yellowley, I.
    International Journal of Machine Tools and Manufacture, 1997, 37 (02): : 119 - 134
  • [9] An upper-bound cutting model for oblique cutting tools with a nose radius
    Seethaler, RJ
    Yellowley, I
    INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 1997, 37 (02): : 119 - 134
  • [10] ALLOWING FOR NOSE RADIUS EFFECTS IN PREDICTING THE CHIP FLOW DIRECTION AND CUTTING FORCES IN BAR TURNING.
    Young, H.T.
    Mathew, P.
    Oxley, P.L.B.
    Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science, 1987, 201 (03): : 213 - 226
12345