Failure mechanisms of a PCD tool in high-speed face milling of Ti-6Al-4V alloy

被引：0

作者：

机构：

[1] Li, Anhai

[2] Zhao, Jun

[3] Wang, Dong

[4] Zhao, Jiabang

[5] Dong, Yongwang

来源：

Zhao, J. (zhaojun@sdu.edu.cn) | 1959年 / Springer London卷 / 67期

关键词：

High-speed milling tests were carried out on Ti-6Al-4V titanium alloy with a polycrystalline diamond (PCD) tool. Tool wear morphologies were observed and examined with a digital microscope. The main tool failure mechanisms were discussed and analyzed utilizing scanning electron microscope, and the element distribution of the failed tool surface was detected using energy dispersive spectroscopy. Results showed that tool flank wear rate increased with the increase in cutting speed. The PCD tool is suitable for machining of Ti-6Al-4V titanium alloy with a cutting speed around 250 m/min. The PCD tool exhibited relatively serious chipping and spalling at cutting speed higher than 375 m/min, within further increasing of the cutting speed the flank wear and breakage increased greatly as a result of the enhanced thermal-mechanical impacts. In addition, the PCD tool could hardly work at cutting speed of 1,000 m/min due to the catastrophic fracture of the cutting edge and intense flank wear. There was evidence of workpiece material adhesion on the tool rake face and flank face in very close proximity to the cutting edge rather than on the chipped or flaked surface, which thereby leads to the accelerating flank wear. The failure mechanisms of PCD tool in high-speed wet milling of Ti-6Al-4V titanium alloy were mainly premature breakage and synergistic interaction among adhesive wear and abrasive wear. © Springer-Verlag London 2012;

D O I：

暂无

中图分类号：

学科分类号：

摘要：

Journal article (JA)

引用

页码：9 / 12

共 50 条

[1] Failure mechanisms of a PCD tool in high-speed face milling of Ti-6Al-4V alloy
Li, Anhai
Zhao, Jun
Wang, Dong
Zhao, Jiabang
Dong, Yongwang
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2013, 67 (9-12): : 1959 - 1966
[2] Failure mechanisms of a PCD tool in high-speed face milling of Ti–6Al–4V alloy
Anhai Li
Jun Zhao
Dong Wang
Jiabang Zhao
Yongwang Dong
The International Journal of Advanced Manufacturing Technology, 2013, 67 : 1959 - 1966
[3] Tool wear in high-speed milling of Ti-6Al-4V alloy
Zhang, Song
Li, Jianfeng
Liu, Fengshi
Jiang, Feng
ADVANCES IN MACHINING AND MANUFACTURING TECHNOLOGY IX, 2008, 375-376 : 435 - 439
[4] SURFACE INTEGRITY OF HIGH-SPEED FACE MILLED Ti-6Al-4V ALLOY WITH PCD TOOLS
Li, Anhai
Zhao, Jun
Dong, Yongwang
Wang, Dong
Chen, Xiaoxiao
MACHINING SCIENCE AND TECHNOLOGY, 2013, 17 (03) : 464 - 482
[5] Progressive tool failure in high-speed dry milling of Ti-6Al-4V alloy with coated carbide tools
Li, Anhai
Zhao, Jun
Luo, Hanbing
Pei, Zhiqiang
Wang, Zeming
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2012, 58 (5-8): : 465 - 478
[6] Progressive tool failure in high-speed dry milling of Ti-6Al-4V alloy with coated carbide tools
Anhai Li
Jun Zhao
Hanbing Luo
Zhiqiang Pei
Zeming Wang
The International Journal of Advanced Manufacturing Technology, 2012, 58 : 465 - 478
[7] Simulation of The High-speed Milling Temperature of Titanium Alloy Ti-6Al-4V
Huang, Xinchun
Yao, Changfeng
Zhang, Dinghua
Ren, Junxue
ADVANCED MANUFACTURING TECHNOLOGY, PTS 1-3, 2011, 314-316 : 1171 - 1175
[8] The performance of PCD tools in high-speed milling of Ti6Al4V
Gert Adriaan Oosthuizen
Guven Akdogan
Nico Treurnicht
The International Journal of Advanced Manufacturing Technology, 2011, 52 : 929 - 935
[9] The performance of PCD tools in high-speed milling of Ti6Al4V
Oosthuizen, Gert Adriaan
Akdogan, Guven
Treurnicht, Nico
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2011, 52 (9-12): : 929 - 935
[10] Tool wear and cutting forces variation in high-speed end-milling Ti-6Al-4V alloy
S. Zhang
J. F. Li
J. Sun
F. Jiang
The International Journal of Advanced Manufacturing Technology, 2010, 46 : 69 - 78

← 1 2 3 4 5 →